EasyManua.ls Logo

Vector POWERFORCE VEC074 User Manual

Vector POWERFORCE VEC074
7 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
POWERFORCE
AUTOMATIC BATTERY CHARGER
OWNER’S MANUAL & WARRANTY INFORMATION
12 VOLT 2/10 AMPERE WITH 55 / AMPERE ENGINE START ASSIST
VEC074
IMPOR
TANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery charger Model VEC074
4140 SW 28TH WAY, FT. LAUDERDALE, FL 33312 • TEL: 945-584-4446 • FAX: 954-584-5556
GENERAL BATTERY SAFETY:
1. To reduce risk of battery explosion, follow these instructions and those published by the battery manufac-
turer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary mark-
ing on these products and on engine.
2. Use charger for charging a LEAD-ACID battery only. It is not intended to supply power to a low voltage
electrical system other than in an automotive application. Do not use battery charger for charging dry-
cell batteries that are commonly used with home and portable appliances. These batteries may burst and
cause injury to persons and damage to property.
3. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons.
4. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.
5. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could
result in a risk of fire and electric shock. If extension cord must be used, make sure:
a. That pins on plug of extension cord are the same number, size, and shape as those of plug on charger.
b. That extension cord is properly wired and in good electrical condition; and
c. That wire size is AWG #18 (18 gauge) to 100 feet and AWG #16 for distances over 100 feet.
6. Do not operate charger with damaged cord or plug - replace the cord or plug immediately.
7. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take
it to a qualified serviceman.
8. Do not disassemble charger; take it to a qualified serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
9. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.
Turning off controls will not reduce this risk.
10. Do not expose charger to rain or snow.
11. Never charge a frozen battery
WORKING IN VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE
EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF
UTMOST IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER, YOU READ THIS
MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
Question and Answer IconNeed help?

Do you have a question about the Vector POWERFORCE VEC074 and is the answer not in the manual?

Vector POWERFORCE VEC074 Specifications

Power IconPower
input voltage120 VAC
frequency60 Hz
current1.3 amperes
Weight and Dimensions IconWeight and Dimensions
height5.5" (14.0 cm)
width9.5" (24.1 cm)
depth6.5" (16.5 cm)
weight7 lbs

Summary

General Battery Safety

Battery Safety Instructions

Detailed safety instructions for handling lead-acid batteries and charger operation.

Operational Safety and Precautions

Personal Safety, Preparation, and Location

Personal safety, preparation steps, and charger location guidelines for safe operation.

DC Connection Safety

Crucial safety precautions for connecting and disconnecting the charger's DC output clips.

Introduction and Features

Product Overview and Capabilities

Overview of the Vector VEC074 battery charger, its features, and intended uses.

Charger Controls

Control Functions Overview

Explanation of the Charge/Assist switch, charge rate selector, and ammeter indicators.

Charging Procedures

Charging in Vehicle

Step-by-step guide for charging a battery while it remains installed in a vehicle.

Charger Protection and Activation

Information on the circuit breaker and the process of pre-charge activation for batteries.

Advanced Charging and Maintenance

Off-Vehicle Charging and Start Assist

Procedure for charging batteries outside a vehicle and using the engine start assist function.

Maintenance and Cold Battery Troubleshooting

Charger upkeep, and troubleshooting for cold batteries.

Troubleshooting and Appendices

Troubleshooting Various Issues

Addressing sulfated, short-circuited, and unresponsiveness issues, plus appendices.

Related product manuals