Ventec Life Systems VOCSN User Manual (English)

Other manuals for Ventec Life Systems VOCSN

Quick Start Guide2 pages

Clinical And Technical Manual225 pages

Questions and Answers:

J
James FernandezSep 13, 2025
What should I do if the Very Low FiO2 alarm activates on my Ventec Life Systems Medical Equipment?
- A
  Alicia WatsonSep 14, 2025
  If the Very Low FiO2 alarm activates on your Ventec Life Systems Medical Equipment, ensure the device's air inlets are not blocked and there is adequate airflow around it. Remove any oxygen sources connected to the device or the patient circuit. If the alarm resolves, troubleshoot problems with the oxygen source. If the alarm persists, there may be a problem with the device's oxygen sensor; contact your local Ventec Life Systems representative for service.
T
Tricia OrtegaAug 25, 2025
What to do if the Ventec Life Systems Medical Equipment shows a high pressure alarm?
- R
  Rachel MooreAug 26, 2025
  Ensure the High Pressure alarm on your Ventec Life Systems Medical Equipment is appropriately set for the patient's condition. Check for any blockages or obstructions in the circuit and patient airway, such as saturated filters, in-line suction catheters, or patient secretions. If the problem persists, replace the patient circuit.
A
Amy BurnettAug 26, 2025
What causes patient desaturation when using Ventec Life Systems VOCSN?
- A
  Andrew ParsonsAug 27, 2025
  If you observe patient desaturation while using the Ventec Life Systems Medical Equipment, first ensure the O2 monitoring equipment is connected to the patient. Run a Pre-Use Test. Ensure the patient circuit O2 Tube is properly connected so that the rubber connector is flush against the O2 tube connection side of the device. Also, check that any external oxygen source is properly connected and not depleted. Note that it may take up to 1 hour for oxygen alarms to resolve after fixing an issue with the O2 tube connection.
T
Tammy OliverAug 27, 2025
What to do if apnea activates on Ventec Life Systems Medical Equipment?
- B
  Brenda NobleAug 27, 2025
  If the Apnea alarm activates on your Ventec Life Systems Medical Equipment, ensure the Apnea alarm is set appropriately, considering the patient’s Breath Rate and spontaneous rate. Also, ensure the Flow Trigger control is set correctly. Check the patient triggered icon and waveforms to see if the patient is attempting to initiate breaths. If not, the alarm is working as intended. Check for issues with patient triggering, such as low drive due to medication, secretions, or excessive mask or cuff leak. For Active circuits, turn on Leak Compensation if needed. If the problem continues, replace the circuit.
T
Thomas BurnettAug 27, 2025
How to troubleshoot a 'Check Patient Circuit' error on Ventec Life Systems VOCSN Medical Equipment?
- R
  Ronald BrewerAug 27, 2025
  If you receive a Check Patient Circuit alarm on your Ventec Life Systems Medical Equipment, run a Pre-Use Test. For Passive circuits, check the VOCSN Leak monitor and resolve any unintentional leaks in the patient circuit or around the patient interface, ensuring the exhalation valve is not obstructed. For Active circuits, ensure the flow sensor tubing is securely connected to the device and the active exhalation valve. If using a nebulizer, install a filter between the nebulizer and the patient circuit exhalation valve. For heated circuits, ensure there is no water accumulation in the tubing or valve. If the problem persists, replace the patient circuit.
C
cboydSep 9, 2025
What causes a low PEEP alarm on Ventec Life Systems VOCSN?
- A
  Amanda MitchellSep 9, 2025
  If the Low PEEP alarm activates on your Ventec Life Systems Medical Equipment, check the VOCSN Leak monitor and resolve any unintentional leaks in the patient circuit or around the patient interface. Run a Pre-Use Test. If the alarm continues, replace the patient circuit.
C
charles57Sep 7, 2025
How do I troubleshoot a low inspiratory pressure alarm on Ventec Life Systems VOCSN?
- B
  bakertracySep 8, 2025
  If the Low Inspiratory Pressure alarm activates on your Ventec Life Systems Medical Equipment, ensure the alarm is set below the patient peak inspiratory pressure, considering changes in airway resistance and/or lung recruitment. Check the VOCSN Leak monitor and resolve any unintentional leaks in the patient circuit or around the patient interface. If the problem persists, replace the patient circuit.
B
Bryce EatonSep 8, 2025
What should I do if the low minute volume alarm activates on my Ventec Life Systems VOCSN Medical Equipment?
- M
  margaret24Sep 9, 2025
  If the Low Minute Volume alarm activates on your Ventec Life Systems Medical Equipment, ensure the alarm is set appropriately, considering changes in patient breathing habits at night. Check the VOCSN Leak monitor and resolve any unintentional leaks in the patient circuit and around the patient interface. If using a trach tube, ensure the cuff is properly inflated. During pressure-control ventilation, check the patient for reduced lung compliance or airway blockages.
E
Emily BrooksSep 2, 2025
Why is the performance of my Ventec Life Systems Medical Equipment changing?
- C
  Catherine CooperSep 2, 2025
  If you notice changes in the performance of your Ventec Life Systems Medical Equipment, move it away from potential sources of electromagnetic interference (EMI) such as MRI equipment, medical imaging systems, security systems, appliances, wireless communications equipment, computers, and televisions. You can also try restarting the device by pressing the On/Off button. If the issue persists, contact Ventec Life Systems for service.
X
xstokesSep 1, 2025
Why is abnormally warm gas flowing through the Ventec One-Circuit on my Ventec Life Systems Medical Equipment?
- K
  Kyle JensenSep 1, 2025
  If abnormally warm gas is flowing through the Ventec One-Circuit of your Ventec Life Systems Medical Equipment, the air filter may be clogged; clean and replace it, replacing it if damaged. Ensure the device is properly ventilated, away from cluttered areas or heat sources. Contact Ventec Life Systems for service if the issue persists.

Ventec Life Systems VOCSN Specifications

General

Oxygen Concentration	21-100%
FiO2 Range	21-100%
Power Source	AC Power, DC Power, Internal Battery
Ventilation Modes	SIMV, CPAP
Weight	18 lb (8.2 kg) with battery
Tidal Volume	50-2000 mL
Respiratory Rate	1-60 BPM
PEEP	0-20 cmH2O
Pressure Support	0-30 cmH2O

Related product manuals

Ventec Life Systems Vocsn V+Pro

194 pages

Ventec Life Systems V-Home

182 pages

Ventec Life Systems VOCSN Clinical Quick Start Guide

Table of Contents

Other manuals for Ventec Life Systems VOCSN

Questions and Answers:

Ventec Life Systems VOCSN Specifications

Related product manuals