Vesta VRS-199 - User Manual

To Next Page

REVOLUTION WATER

HEATER

User Manual

Model

VRP-150 VRP-199

VRS-150 VRS-199

Keep this manual near the water heater for future reference

whenever maintance or service is required.

* Lead Free

* The wetted surface of this product contacted by consumable water contains less than one quarter of one percent (0.25%) of lead by weight.

- The installation must conform with local codes or, in

the absence of local codes, the National Fuel Gas Code,

ANSI Z223.1/NFPA 54 and/or CSA B149.1, Natural Gas

and Propane Installation Code.

- When applicable, the installation must conform with

the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280 and/or CAN/CSA Z240

MH Series, Mobile Homes.

WARNING: If the information in these

instructions is not followed exactly, a fire or

explosion may result causing property damage,

personal injury, or death.

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

 WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

- Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

Other manuals for Vesta VRS-199

Quick Installation Guide2 pages

Need help?

Do you have a question about the Vesta VRS-199 and is the answer not in the manual?

Summary

Front Panel

Digital Display and Icons

Explains icons and digital display on the front panel for operation status and information.

Buttons

Details the function of each button on the front panel for controlling the water heater.

Operating the Water Heater

Turning the Water Heater On or Off

Setting the Water Temperature

Guide to adjusting the water temperature setting on the front panel using UP/DOWN buttons.

Maintaining the Water Heater

Flushing the Heat Exchanger

Detailed instructions for flushing the heat exchanger annually or in hard water conditions.

Protecting the Water Heater from Freezing

Troubleshooting

Basic Problems

Table of common issues, potential causes, and recommended solutions for basic problems.

Error Codes

Chart listing error codes, their causes, and self-diagnosis/action remedies.

Summary

Front Panel

Digital Display and Icons

Explains icons and digital display on the front panel for operation status and information.

Buttons

Details the function of each button on the front panel for controlling the water heater.

Operating the Water Heater

Turning the Water Heater On or Off

Setting the Water Temperature

Guide to adjusting the water temperature setting on the front panel using UP/DOWN buttons.

Maintaining the Water Heater

Flushing the Heat Exchanger

Detailed instructions for flushing the heat exchanger annually or in hard water conditions.

Protecting the Water Heater from Freezing

Troubleshooting

Basic Problems

Table of common issues, potential causes, and recommended solutions for basic problems.

Error Codes

Chart listing error codes, their causes, and self-diagnosis/action remedies.

This document is a user manual for the Revolution Water Heater, models VRP-150, VRP-199, VRS-150, and VRS-199. It provides essential information for safe operation, maintenance, and troubleshooting of the device.

Function Description

The Revolution Water Heater is a tankless gas-fired water heater designed to provide on-demand hot water. It features a digital display and various icons to monitor its operational status, including water temperature, flow rate, and combustion load. The device is equipped with safety features and is designed for both household and commercial use, with different temperature ranges available for each. It is certified to NSF/ANSI 5 & 372, Low NOx (SCAQMD Rule 1146.2 compliant), ENERGY STAR certified, and AHRI certified, indicating its efficiency and compliance with industry standards. The product is also lead-free, meaning the wetted surfaces contain less than 0.25% lead by weight.

Important Technical Specifications

Models: VRP-150, VRP-199, VRS-150, VRS-199.
Gas Type: Natural Gas or Propane (installation must conform to relevant codes).
Power Supply: 120 V-1 PH-60 Hz (required for operation).
Temperature Range (Household Use): 98°F (37°C) to 140°F (60°C).
- 98°F (37°C) to 120°F (50°C) in 2°F increments.
- 120°F (50°C) to 140°F (60°C) in 5°F increments.
Temperature Range (Commercial Use): 98°F (37°C) to 180°F (82°C).
- 140°F (60°C) to 180°F (82°C) in 10°F increments.
Safety Certifications: NSF/ANSI 5 & 372, Low NOx (SCAQMD Rule 1146.2), ENERGY STAR, AHRI Certified.
Lead Content: Wetted surfaces contain less than 0.25% lead by weight.
Warranty:
- Heat Exchanger: 15 years (Residential), 8 years (Commercial).
- All Other Parts and Components: 5 years (Residential), 3 years (Commercial).
- Reasonable Labor: 1 year (Residential and Commercial).
Installation: Must conform to local codes, National Fuel Gas Code ANSI Z223.1/NFPA 54, and/or CSA B149.1, Natural Gas and Propane Installation Code. For manufactured homes, it must conform to Title 24 CFR, Part 3280 and/or CAN/CSA Z240 MH Series.
Recirculation (VRP models only): Requires recirculation piping and proper Dip Switch setting.

Usage Features

Front Panel Controls:
- Power Button: Turns the water heater on or off.
- Mode Button: Changes the display mode to view different operational information (e.g., IN temperature, OUT temperature, LPM/GPM, % combustion load).
- Up/Down Buttons: Adjust the water temperature setting.
Digital Display: Shows current water temperature, error codes, and other operational data.
Icons:
- Pump: Indicates recirculation pump operation (VRP models).
- Cascade: Indicates cascade operation.
- LPM/GPM: Displays flow rate of hot water supply in Liters Per Minute or Gallons Per Minute.
- Error: Indicates an error condition.
- Combustion: Indicates gas burner operation.
- %: Indicates combustion load in percentage.
- OUT: Indicates hot water supply temperature.
- IN: Indicates cold water inlet temperature.
Temperature Setting: Users can adjust the desired hot water temperature. Caution is advised for temperatures above 125°F (51°C) due to scalding risk, especially for children, the disabled, and the elderly. A 5-second hold of the "down" button is required to unlock temperature changes between 120°F (50°C) and 125°F (52°C).
Mode Switching: The device can switch between household and commercial modes by pressing the power button to turn off the unit, then simultaneously pressing the MODE and "down" buttons for 5 seconds. "LAHI" indicates commercial mode, and "LALO" indicates household mode.
Remote Controller (VD-100, optional): Allows remote control of power, temperature setting, mode selection, and recirculation (for VRP models).
Freeze Protection: The water heater has a built-in freeze protection function that warms the unit when the internal temperature drops below 43°F (6°C), provided the power supply is connected.

Maintenance Features

Draining the Water Heater: Necessary for maintenance or to prevent freezing during extended periods of non-use. Involves turning off power and gas, closing water supply valves, opening hot water faucets, and draining water from the inlet nipple filter or drain plug.
Cleaning the Inlet Nipple Filter: The filter should be removed, rinsed with clean water, and reinserted after draining the water heater.
Cleaning the Recirculation Filter (VRP models only): Involves removing the front cover, loosening screws to remove the filter, rinsing it with clean water, and reassembling.
Cleaning the Air Intake Filter: Recommended every 2-3 months. Involves turning off power, removing the front cover, locating and removing the filter, rinsing it with clean water, drying it completely, and reinserting. A clogged filter can cause operational issues or errors.
Flushing the Heat Exchanger: Required annually, or more often in hard water conditions. This is a more complex procedure involving disconnecting power, closing shutoff valves, connecting hoses to a circulation pump, circulating a cleaning solution (e.g., 4 gallons of virgin, food-grade white vinegar) for at least 45 minutes, then rinsing with fresh water.
Maintenance Schedules:
- Daily: Check for combustible/flammable materials and air contaminants, visually inspect the exterior.
- Monthly: Inspect condensate trap and PVC fittings, check piping for leaks (water and gas), inspect vent piping for leakage and blockage.
- Every 6 Months: Inspect piping for leaks, inspect vent piping for leakage and blockage, test pressure relief valve operation (with caution to avoid hot water contact and water damage).
- Periodically (Service Technician): Inspect interior, clean condensate trap and fill with fresh water, clean air intake filter, check for leaks (gas, water, flue, condensate), check system pressure (gas, water), check ignition and flame rod, check wiring connections.
Troubleshooting: The manual provides a table of basic problems, possible causes, and recommended actions, including error codes and their self-diagnosis/actions. For persistent issues or error codes, contacting a qualified installer, licensed professional, or VST technical support is advised.