Viega Picco 6 - User Manual

Questions and Answers

W
whaasAug 19, 2025
What to do if the press jaw cannot be opened after pressing with Viega Picco 6?
- S
  Scott AriasAug 19, 2025
  If the press jaw cannot be opened after pressing with your Viega Power Tool, it may be due to several reasons: * The pressing was unable to be completed. In this case, press the Reset button, remove the press jaw from the press connector, inspect the press jaw, and repeat the pressing. * The press jaw dimension does not match the press connector. Ensure you are using a press jaw that matches the press connection dimension. * The press jaw was not positioned square to the pipe axis on the press connector. Make sure the press jaw is correctly positioned square to the pipe axis and repeat the pressing. * The press contour is incorrect. Check the press jaw, have it repaired if needed, and repeat the pressing with an operational press jaw.
R
Richard LangAug 21, 2025
Why Viega Power Tool is not ready for operation after pressing the Start button?
- S
  Steven PriceAug 21, 2025
  If your Viega Power Tool is not ready for operation after pressing the Start button, it could be due to: a fully discharged or faulty battery, so you should use a fully charged battery. Another potential cause is that the battery is not correctly inserted; ensure it is correctly located in the mounting bracket.
C
Cassie MckayAug 23, 2025
What to do if Viega Picco 6 switches off during pressing?
- J
  jessica24Aug 23, 2025
  If your Viega Power Tool switches off during pressing and the LED is flashing, the battery is almost flat. Use a fully charged battery to resolve this issue.
S
Stacey MccarthyAug 26, 2025
Why Viega Picco 6 Power Tool motor runs, but the press machine does not complete the pressing?
- C
  Chad PattersonAug 26, 2025
  If the motor of your Viega Power Tool runs but the pressing is not completed, this could be because the oil level is too low. In this case, send the press machine to your nearest service partner for inspection and maintenance.
M
Melanie KingAug 27, 2025
What does it mean when the LED flashes three times on Viega Picco 6 Power Tool?
- A
  Ashley BrownAug 28, 2025
  When the LED flashes three times on your Viega Power Tool, the display repeats, and the maintenance symbol is illuminated while the machine still works, it means that 30,000 strokes have been reached or exceeded. Maintenance is due, and the safety shutdown will occur after a further 2,000 pressings.
J
Joshua MccartyAug 30, 2025
What to do if LED flashes twice on Viega Picco 6 and the temperature symbol is illuminated?
- D
  david22Aug 30, 2025
  If the LED flashes twice then pauses and the temperature symbol is illuminated on your Viega Power Tool, it indicates that the press machine is outside the permitted temperature range. Bring the press machine and the rechargeable battery to the recommended temperature range in a well-ventilated environment.
E
evansmichaelSep 1, 2025
What does it mean if LED flashes three times on Viega Picco 6 Power Tool and the press machine does not carry out pressing?
- A
  angel90Sep 1, 2025
  If the LED flashes three times, the maintenance symbol is illuminated, and the Viega Power Tool does not carry out pressing, it means that 32,000 strokes have been reached, and the press machine has activated the safety shutdown function.
B
Bethany MckenzieSep 3, 2025
Why oil escapes from Viega Picco 6?
- A
  Alyssa DixonSep 3, 2025
  If oil escapes from your Viega Power Tool, it indicates a faulty seal in the casing or a mechanical problem. Send the press machine to your nearest service partner for inspection and maintenance.
N
Nicole SwansonSep 5, 2025
Why is my Viega Picco 6 press connector incorrectly pressed?
- M
  Micheal WilliamsonSep 5, 2025
  An incorrectly pressed Viega Power Tool press connector may occur if: * The press jaw dimension does not match the press connector, so use a matching press jaw. * The press jaw wasn't positioned square to the pipe axis; repeat the pressing, ensuring square positioning. * The press contour is incorrect; check the press jaw and have it repaired if needed. * The press machine is malfunctioning.
C
Carl LeeSep 7, 2025
What to do if Viega Picco 6 press machine is not ready for operation?
- M
  Mallory DavisSep 7, 2025
  If your Viega Power Tool press machine isn't starting after pressing the Start button, it might be due to a fully discharged or faulty battery. Try using a fully charged battery. Also, ensure the battery is correctly located in the mounting bracket.

Summary

About these instructions for use

Target Groups

Information for heating and plumbing experts and trained personnel.

Safety Symbol Explanation

Explains warning symbols like DANGER, WARNING, CAUTION, NOTICE.

Translated Version Information

Explains the scope and basis of the translated instructions.

Abbreviated Terms Guide

Lists terms and their abbreviated forms used in the manual.

Product Information

Standards and Regulations

Lists applicable standards and regulations for Germany/Europe.

General Electrical Tool Safety

Provides general safety instructions applicable to electrical tools.

Electrical Safety Precautions

Details crucial safety measures related to electrical aspects of tools.

Personal Safety Measures

Details essential personal safety measures for operating tools.

Power Tool Use and Care

Instructions for using and maintaining power tools correctly.

Battery Tool Use and Care

Guidelines for safe operation and maintenance of battery tools.

Tool Service Information

Information on servicing power tools by qualified personnel.

Basic Safety Rules

Core safety principles for tool operation and work practices.

Intended Use and Areas of Use

Defines the intended application of the press machine.

Product Overview and Scope of Delivery

Lists the components included in the scope of delivery.

Pressgun 6 Machine Components

Illustrates and labels the main components of the Pressgun 6.

Rechargeable Battery and Charger Details

Details control elements on the rechargeable battery and charger.

Gripping Surfaces on the Press Machine

Illustrates correct gripping points for safe operation.

Technical Data

Presents detailed technical specifications for the press machine.

Specification Plate Explanation

Explains the information found on the product's specification plate.

Compatible Accessories

Lists recommended original accessories for the press tools.

Operating Mode

Explains how the electro-hydraulically operated press machine functions.

Control Elements and Indicators

Describes the press machine's display, control process, and standby mode.

Status LED and Button Functions

Explains LED indicators, start button, reset button, and cylinder head.

Handling

Transport and Storage Guidelines

Provides essential guidelines for safe transport and storage.

Commissioning Procedure

Step-by-step guide for setting up and preparing the machine.

Carrying Out the Pressing Process

Instructions for performing the pressing operation correctly.

Aborting the Pressing Process

Explains how to interrupt or cancel a pressing operation.

Troubleshooting Common Issues

Lists common faults, their causes, and solutions.

Care and Maintenance

Covers cleaning, performing checks, and general inspection.

Maintenance Interval and Labels

Specifies maintenance intervals and explains related labels.

Disposal Instructions

Provides guidelines for environmentally friendly disposal.

Appendix

Warranty Information

Details the warranty period and conditions for Viega tools.

EC Declaration of Conformity

Provides the EC Declaration of Conformity for the product.

Service Partner Contact

Lists contact information for service and repair partners.

Viega Picco 6 Specifications

General

Brand	Viega
Model	Picco 6
Category	Power Tool
Language	English