Need help?Do you have a question about the Viessmann WAGO KNX/TP gateway and is the answer not in the manual?
Explains safety symbols and their meanings.
Defines the intended audience as qualified contractors.
Lists applicable regulations and standards.
Details critical safety procedures for system operation, covering flue gas and water leaks.
Provides guidance on safe repair practices and component replacement.
Instructions on how to dispose of packaging waste.
Explains the meaning of various symbols used in the manual.
Defines the proper installation and use of the gateway.
Details about the WAGO KNX/TP gateway and its purpose.
Lists the capabilities of the gateway in conjunction with KNX/EIB.
Information on how to find spare parts for the gateway.
Diagram showing the system components and their connections.
Lists the steps and responsibilities for installation.
Detailed steps for installing the gateway and power supply.
Details standard and on-site connecting cable specifications.
Step-by-step instructions for physically mounting the gateway.
Step-by-step instructions for physically mounting the power supply unit.
Details the physical connections and interfaces of the gateway.
Instructions for connecting and disconnecting electrical wires.
Description of the gateway's controls like switches and selectors.
Explanation of the status LEDs and their meanings.
Details about the power supply unit and its specifications.
Instructions for connecting the CAN bus to the gateway.
Instructions for connecting the plug-in attachment for the CAN bus.
Guidance on establishing the KNX network connection.
General information and safety warnings regarding the power supply.
Guidelines for installing isolators for non-earthed conductors.
Step-by-step instructions for connecting cores in the power supply.
Details the power supply connection using a mains isolator.
Details the power supply connection independent of a mains isolator.
Step-by-step guide for commissioning the gateway, including LED indicators.
Instructions for removing the end clamp of the gateway.
Instructions for removing the KNX terminal from the gateway.
Instructions for removing the CAN terminal from the gateway.
Instructions for removing the controller unit.
Instructions for safely removing the power supply unit.
Technical specifications for the WAGO KNX/TP gateway.
Technical specifications for the power supply unit.
Guidance on decommissioning the system and disposing of components.
Information regarding directives compliance and CE marking requirements.
Explains safety symbols and their meanings.
Defines the intended audience as qualified contractors.
Lists applicable regulations and standards.
Details critical safety procedures for system operation, covering flue gas and water leaks.
Provides guidance on safe repair practices and component replacement.
Instructions on how to dispose of packaging waste.
Explains the meaning of various symbols used in the manual.
Defines the proper installation and use of the gateway.
Details about the WAGO KNX/TP gateway and its purpose.
Lists the capabilities of the gateway in conjunction with KNX/EIB.
Information on how to find spare parts for the gateway.
Diagram showing the system components and their connections.
Lists the steps and responsibilities for installation.
Detailed steps for installing the gateway and power supply.
Details standard and on-site connecting cable specifications.
Step-by-step instructions for physically mounting the gateway.
Step-by-step instructions for physically mounting the power supply unit.
Details the physical connections and interfaces of the gateway.
Instructions for connecting and disconnecting electrical wires.
Description of the gateway's controls like switches and selectors.
Explanation of the status LEDs and their meanings.
Details about the power supply unit and its specifications.
Instructions for connecting the CAN bus to the gateway.
Instructions for connecting the plug-in attachment for the CAN bus.
Guidance on establishing the KNX network connection.
General information and safety warnings regarding the power supply.
Guidelines for installing isolators for non-earthed conductors.
Step-by-step instructions for connecting cores in the power supply.
Details the power supply connection using a mains isolator.
Details the power supply connection independent of a mains isolator.
Step-by-step guide for commissioning the gateway, including LED indicators.
Instructions for removing the end clamp of the gateway.
Instructions for removing the KNX terminal from the gateway.
Instructions for removing the CAN terminal from the gateway.
Instructions for removing the controller unit.
Instructions for safely removing the power supply unit.
Technical specifications for the WAGO KNX/TP gateway.
Technical specifications for the power supply unit.
Guidance on decommissioning the system and disposing of components.
Information regarding directives compliance and CE marking requirements.
General| Category | Gateway |
|---|---|
| Communication protocol | KNX/TP |
| Manufacturer | Viessmann |
| Protection Class | IP20 |
| Operating Temperature | 0°C to +45°C |
| Relative Humidity | ≤ 93% (non-condensing) |
To Next Page
