Viking DFBB363 - Bottom Mount Dimensions; 36 Bottom Mount; Bottom Mount Specifications

Reverse dimensions
for other end.
1
/2
”
(
1.
27
c
m)
1-1/2”
(3.8
1
cm)
1/4”
Ra
diu
s
(.64 c
m)
2-
3/
4”
(6.98 cm
)
1
/2
”
(
1.
2
7
c
m)
3/4
”
(
1.
90
cm)
1/2
”
(1.27
c
m)
1/8
”
(.31 cm)
1/
2”
(1.
27 cm)
1/4”
Radius
1/4” Radius
(1.2
c
m)
(1.2 cm)
1/4”
Radius
(.64
c
m)
7/8
”
(
2.
22
cm
)
1/2
”
(1.27 c
m)
34”
(86
.36
cm
)
34”
(86
.36
cm)
3/4”
(1.90 c
m)
1/2”
(1.2
7 c
m)
3/4
”
(1.
90
cm)
3-3/4”
(9.5
2 c
m)
3-3/4”
(9.52
cm)
3-5/8
”
(9.20
cm)
33
-15
/16
”
(86
.20
cm
)
3”
(7.6
2 c
m)
3”
(7.6
2 c
m)
3/4
”
(1.9
0 cm)
35-1/2
”
(90
.17
cm
)
1/2
”
(1.
27
cm)
3-1/8”
(7.
93
c
m)
Opt
ion
al
hin
ge
cov
er
32-
3/1
6”
(81
.75 cm
)
5-17
/32
”
(14
.10
cm
)
4-11
/64
”
(10
.59
cm
)
30-27/
32”
(78
.34
cm
)
3 2
5/3
2”
(9.
60
c
m)
27/3
2”
(.8
4 c
m)
9/1
6”
(1.
42 c
m
)
1/4
”
(.6
35 c
m)
16.
5˚
20.
0˚
Custom Grille Dimensions (Bottom Mount)
7
35-
1/4”
(89.5 cm
)
23-1/
16”
(58
.6 c
m)
3/4”
(1.
9 c
m)
35-
1/4”
(89.5
cm
)
34-3
/8”
to notch
(86.6 c
m)
7/8”
(2.2 c
m)
5/8”
(1.6
cm
)
51-7/
8”
(13
1.8 c
m)
51-1/4”
(13
0.2 c
m)
3/4”
(1.
9 c
m)
Note
: Co
rne
r n
otch is
fo
r l
eft
hing
e d
oor.
(R
ever
se for
ri
ght
hi
nge
)
See
pa
ge
50 f
or
cut
out
in
str
uct
ion
s
7/8”
(2.2c
m)
5/8
”
(1.6
cm
)
1/8”
(0.3 cm)
2”
(5.1 cm
)
For Models made
before 9/22/06
Note: Inset shown upside down.
1-1
3/16”
(4.
60
cm)
5/
8”
5/8”
(1.
6 c
m)
(1.6 cm)
3”
(7.
62 c
m)
3/32
”
(.2
4 c
m)
5/8”
5/
8”
(1.
6 c
m)
For Models made
after 9/22/06
Note: Inset shown upside down
Overlay Dimensions (Bottom Mount)
6
36” Custom Panels 36” Custom Grille
Note: Panel overlays must be dry, solid, straight one
piece panels. The use of multiple panel pieces to
achieve the dimensions is not recommended.
Note: If 1/4” back panel is used, the dimensions are
1/4” smaller than the dimensions shown on the top, left
and right side. At the bottom, the 1/4” back panel
should be 5/8” smaller than the dimensions shown.