K-1900-5
K-1900-5
Hot-Line Touch
Tone Dialer
April 4, 2008
Replace Dedicated Phone Lines with a
Touch Tone Hot-Line Dialer
• Touch Tone programmable
• Telephone line powered
• Non-volatile E
2
memory (no batteries required)
• Ring detection (won’t dial on inbound calls)
• User programmable security code
• Programmable pauses in one and four second
increments
• Programmable to interrupt user touch tone dialing to
help control fraudulent calls from hand held dialers, etc.
• Programmable dialing speed (normal or fast)
• Can be configured to operate from a contact closure
(Fax Back Document 818)
Power: Telephone line powered (24V DC 20 mA minimum)*
Dimensions: 74mm x 53mm x 25mm (2.9” x 2.1” x 1.0”)
Shipping Weight: .45 kg (1 lb)
Environment: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
Connections: (1) RJ11 plug, (1) RJ11 jack
Dialing Speed: Normal - 120ms on/off, Fast - 50ms on/off
* Note: When installing multiple line powered products (K-1900-5 and E-
10/E-15/E-20A/K-1500-EHF) on the same line, additional talk battery
voltage and loop current may be required.
P
P
r
r
a
a
c
c
t
t
i
i
c
c
e
e
T
T
E
E
L
L
E
E
C
C
O
O
M
M
S
S
O
O
L
L
U
U
T
T
I
I
O
O
N
N
S
S
F
F
O
O
R
R
T
T
H
H
E
E
2
2
1
1
S
S
T
T
C
C
E
E
N
N
T
T
U
U
R
R
Y
Y
TECHNICAL
TECHNICAL
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
• Security and emergency phones
• Interactive point of sale displays
• Apartment security
• Catalog sales
• Automated Teller Machines (ATM’s)
• Replaces leased ring down circuits
• Hot-Line reservation phones for hotels, airlines, car
rentals, etc.
A
A
p
p
p
p
l
l
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
The K-1900-5 will automatically dial a preprogrammed number,
of up to 32 digits, whenever an associated telephone is taken off
hook. Using non-volatile E
2
memory, the K-1900-5 is telephone
line powered and will operate on any loop start central office line
or analog PABX/KSU extension.
The K-1900-5 is easily programmed remotely or locally using a
standard Touch Tone phone.
Why pay the premium of leased or dedicated phone lines?
This product does not eliminate the
possibility of toll fraud! To further protect
against fraudulent calls, use with a TR-1
Toll Restrictor (Fax Back Document 705).
!
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Install the K-1900-5 in series between a telephone and a
C.O. line or analog PABX/KSU station.
1. Call the phone connected to the dialer.
2. Answer phone. Enter , & security code.
3. Enter your spped dial number & #00.
K-1900-5 Technical Practice.
Viking Electronics, Inc.
C.O. Line, Analog
PABX/KSU Station,
or FXS Port*
Standard Analog
Telecom Device
1. Connect the K-1900-5 to a C.O. line or analog PABX/KSU station.
2. From a Touch Tone phone, call another phone connected to the
K-1900-5.
3. Take the phone connected to the dialer off hook (answer the
phone).
4. Enter , followed by the six digit security code (see section D on
the next page). A double beep will indicate that you have
accessed the programming mode.
5. You can now program your speed dial number and the following
features listed in section B below.
Note: Programming from a cell-phone may not be suitable in areas
with weak coverage.
A. Accessing the Programming Mode
* An FXS port lets you connect an analog
telephone or device to an IP network.
To Next Page
Need help?
General
