22
• Use the crevice nozzle (32) to clean hard-to-
reach places.
• The dust brush (33) is intended for gentle
cleaning of furniture.
• The dust attachment (34) is recommended for
cleaning of upholstered furniture.
WET CLEANING MODE
Filling the liquid tank with detergent
• Make sure that the vacuum cleaner is switched
off and unplugged.
• Detach the flexible hose (26) and the liquid
supply pipe (13) from the vacuum cleaner. To
detach it, press any side of the connector (14).
• Pull the upper lid lock (3) upwards (pic. D1)
and lift the lid (15) up until it is fixed in vertical
position.
• Remove the receptacle (4) from the vacuum
cleaner and put it aside (pic. D2).
• Remove the liquid tank (18) from the vacuum
cleaner (pic. D3).
• Unscrew the lid of the tank (18) and fill it with
a preliminary prepared detergent solution or
clean warm water at a temperature not exceed-
ing 60°C.
Note: Do not fill the tank (18) with too hot water
at a temperature exceeding 60°C. Do not heat the
filled tank (18) in a microwave oven.
• Screw the tank (18) lid.
• Install the liquid tank (18) and the receptacle (4)
back into the vacuum cleaner.
• Close the upper lid (15) until the lock (3) click-
ing.
• Attach the flexible hose (26) and the pipe (13) to
the vacuum cleaner.
Detergents
• Use only detergents designed for machine
cleaning of carpets, upholstery, and detergents
for machine cleaning of floors or windows.
Other detergents can damage the vacuum
cleaner.
• When preparing cleaning solutions, follow the
directions and dosages indicated on the pack-
aging by their manufacturer.
• Use a floor cleaner to clean smooth floors with
sealed joints (tiles, etc.).
• Use special detergents intended for this pur-
pose to clean carpets and upholstery.
• Keep the detergents away from children.
Attention! To reduce the risk of fire or electric
shock due to damage to the vacuum cleaner inner
parts, use only detergents for machine cleaning
of carpets, floors, windows and upholstery. Do not
use the vacuum cleaner without filters installed
properly to their places.
Preparing the wet cleaning set for operation
• Pull the upper lid lock (3) upwards (pic. B1)
and lift the lid (15) up until it is fixed in vertical
position.
• Install the blue separator (36) with an open side
outlet into the groove in the upper part of the
receptacle (4) (pic. B3) and press on it until
complete fixation (pic. B2). The separator (36)
is intended for wet cleaning.
• Close the upper lid (15). Match the mark on the
base of the hose (26) with the mark on the
vacuum cleaner body. Insert the base of the
flexible hose (26) into the corresponding open-
ing in the front part of the vacuum cleaner. To
fix the hose (26) in the opening, turn the flexible
hose base clockwise until the mark on the
vacuum cleaner body.
• Fix the end of the pipe (13) in the connector (14)
opening until the lock in the front part of the
vacuum cleaner clicks (pic. B5).
• Attach the telescopic pipe (27) to the flexible
hose handle (1) (pic. B6).
• Attach the wet floor cleaning attachment (30) to
the telescopic pipe (27) (pic. B7). The attach-
ment for wet cleaning of upholstery (31) is
attached directly to the flexible hose handle (1).
• Attach the pipe clamps (12) to the telescopic
pipe (27) to fix the liquid detergent supply pipe
(pic. B8). (Used only for the attachment (30)
operation).
• Attach the pipe attachment to the connector
on the handle (1) and turn it clockwise to fix it
(pic. B9).
LIQUID COLLECTING MODE
1.
Follow the assembling instructions for the wet
cleaning mode. The blue separator for wet
cleaning (36) must be installed.
2.
Detach the pipe (13) end from the connec-
tor (14).
3.
Attach the attachment (29) to the telescopic
pipe (27).
Switching the vacuum cleaner on
Before using the unit, unwind the power cord to the
required length and insert the plug into the socket.
The yellow mark on the power cord indicates the
maximum cord length. Do not unwind the power
cord further than the red mark.
Attention! Always switch the vacuum cleaner on
only with a properly installed receptacle filled with
water and properly installed separators and filters.
•
Press the ON/OFF button (9) to switch the
vacuum cleaner on.
•
During the operation you can switch the suction
power depending on the selected type of clean-
To Next Page
Loading...
