23
ing using the sensory controls “+” or “-” (8) of
the control panel.
•
After room cleaning press the on/off button (9)
and remove the power plug from the socket.
•
To wind the power cord, press the winding but-
ton (7). Always hold the cord with your hand to
avoid its whipping and damage.
USING THE VACUUM CLEANER
Attention!
–
To reduce the risk of fire or electric shock,
before the operation always make sure that the
float is installed in the receptacle (4) lid.
–
Do not use the vacuum cleaner without the
properly installed filters.
Dry cleaning mode with water filtration
•
Before use, make sure that you followed the
instructions for preparing for dry cleaning with
water filtration when assembling the vacuum
cleaner and filling the receptacle (4).
•
Make sure that the necessary accessories are
attached to the telescopic pipe (2) or the flex-
ible hose handle (1).
•
Pull the plug to unwind the required length of
the power cord from the back of the vacuum
cleaner and connect the power plug to the
mains socket. Press the button (9) to switch the
vacuum cleaner on.
Warning: Do not pull out the power cord beyond
the yellow mark on it. Pulling the power cord
beyond the red mark may damage the automatic
cord winding system.
•
Use the power setting buttons (8) to set the
suction power according to the type of surface
to be cleaned. The power setting is duplicated
by the corresponding LED indicator lighting up.
•
If the power of the vacuum cleaner has dropped,
switch it off and unplug it from the mains socket
and check the filling of the receptacle (4), the
state of the clogging of the receptacle (4) filter
and the inlet and outlet filters.
Wet cleaning mode (carpets and upholstery)
•
First, carefully clean the surfaces that require
wet cleaning in the dry cleaning mode.
•
When cleaning carpets, plan the order of your
actions to avoid repeated passage over already
cleaned areas of the carpet. When cleaning car-
pets, it is best to start cleaning from the corner
farthest from the entrance to the room.
•
Before cleaning the upholstery, if possible,
check the color fastness to the cleaning agent.
Some types of fabrics, when wet, release a
color pigment that can stain adjacent areas of
the fabric pattern.
Note:
–
If you want to clean the upholstery in the wet
mode, first read the symbols and cleaning
instructions on the information labels on the
product.
–
Never use wet cleaning mode for velvet and
silk.
–
If there is no fabric symbol on the cleaning
label, contact the manufacturer or seller of your
furniture.
–
If the sticker has the symbol or the text “Dry
clean only”, do not use wet cleaning.
–
If you have any doubts whether the wet cleaning
mode is suitable for your carpet or upholstered
furniture, contact their manufacturer or seller
for clarification.
–
To reduce the risk of fire or electric shock due to
damage to the vacuum cleaner parts, use only
detergents for machine cleaning of carpets and
upholstery.
•
Before the use, make sure that you followed the
preparation instructions for the wet cleaning
mode when assembling the vacuum cleaner
and filling the tank (18) with water.
•
Make sure that the necessary accessories are
installed on the telescopic pipe (2) or the flex-
ible hose handle (1). (Use the attachment (30)
for carpets and the attachment (31) for uphol-
stery). Make sure that the liquid supply pipe is
connected to the flexible hose handle (1).
•
Pull out the required length of the power cord of
the vacuum cleaner by the plug and connect it
to the mains socket.
Warning: Do not pull out the power cord beyond
the yellow mark on it. Pulling the power cord
beyond the red mark may damage the automatic
cord winding system.
•
To switch the vacuum cleaner on, press the but-
ton (9) and press the button (17) to switch the
wet cleaning mode on.
•
In the wet cleaning mode set the maximal suc-
tion power with the control buttons (8).
•
Place the selected wet cleaning attachment
over the surface to be cleaned.
•
Press the liquid supply lever (16) to spray and
move the attachment towards you.
•
Release the lever (16) to stop spraying the
liquid.
•
Slowly and re-pass the same place moving
away from you to collect all the remaining water
from the surface.
•
Continue the steps above until you have cleaned
all the required area.
•
During work, make sure that the carpet or fur-
niture upholstery is not excessively moistened.
You can change the amount of liquid supply with
To Next Page
Loading...
