24
the control knob (11) located on the side of the
flexible hose handle (1).
•
If the suction power of the vacuum cleaner has
dropped, it is necessary to stop the wet cleaning
and check the filling level of the receptacle (4).
If the receptacle (4) is filled up to the level mark
“FULL” (1.6 l), the suction will automatically stop.
•
If the vacuum cleaner stops spraying liquid,
immediately switch the vacuum cleaner off by
pressing the button (9) and check the liquid
level in the tank (18). If it is empty and you still
need to continue cleaning, add the solution
according to the instructions given in the chap-
ter “Filling the liquid tank with detergent”.
Wet cleaning mode (hard floors with sealed
joints and windows)
•
Before starting wet cleaning of the room, dry
clean it.
•
When cleaning, plan the order of your actions to
avoid repeated passage over already cleaned
areas of the floor. It is best to start cleaning
from the corner farthest from the entrance to
the room.
Note: To reduce the risk of fire or electric shock
due to damage to the vacuum cleaner parts, use
only detergents for machine cleaning of floors and
windows.
•
Before the use, make sure that you followed the
instructions for the wet cleaning mode when
assembling the vacuum cleaner and filling the
liquid tank (18).
•
Attach the attachment (37) to the wet floor
cleaning attachment (30). To do this, press the
release button on the left side of the attachment
(30) with your index finger. Install the attach-
ment (37) into the upper guide groove of the
holder (pic. H1). Once the attachment (37) is in
the correct position, release the release button
(pic. H2).
•
For wet cleaning of hard floors with sealed joints
(tiles) or windows, attach a rubber squeegee
(38) to the attachment (37) (pic. H3). Insert
the rubber squeegee (38) into the side groove
of the attachment (37) forward with the part
marked with 2 arrows ( ). When
correctly installed, the embossed part of the
squeegee (38) should be on the inside of the
attachment (37) and be fully visible.
•
Pull out the required length of the power cord of
the vacuum cleaner by the plug and connect it
to the mains socket.
•
For wet cleaning of hard floors with sealed joints
or windows with a mop, attach a microfiber cloth
to the fixing strip of the mop attachment. Insert
the assembled mop into the side groove of the
attachment (37) until the fixing stop (pic. Н4).
Make sure that the mop attachment is fully
inserted into the groove.
Note: Make sure the top edge of the microfiber
cloth lines up with the flat edge of the mop attach-
ment.
Warning: Do not pull out the power cord beyond
the yellow mark on it. Pulling the power cord
beyond the red mark may damage the automatic
cord winding system.
•
To switch the vacuum cleaner on, press the but-
ton (9) and press the button (17) to switch the
wet cleaning mode on.
•
In the wet cleaning mode set the maximal suc-
tion power with the control buttons (8).
•
When cleaning with an attachment with the rub-
ber squeegee (38) installed, press the water
squeegee (38) to the surface to be cleaned and
press the detergent supply lever (16) to start the
process of spraying the detergent. At the same
time, move the attachment towards you.
•
Release the lever (16), tilt the attachment (30)
forward and move it slowly in the opposite direc-
tion so that the rubber squeegee (38) is in firm
contact with the floor to completely remove any
remaining water from the area to be cleaned.
Repeat these steps moving the attachment
towards you again.
•
Continue the above steps until all necessary
area is clean.
•
Do the same for window cleaning.
•
If the suction power of the vacuum cleaner has
dropped, stop the wet cleaning and check the
filling level of the receptacle (4). If the recep-
tacle (4) is filled up to the level mark “FULL”
(1.6 l), the suction will automatically stop.
•
If the vacuum cleaner stops spraying liquid,
immediately switch the vacuum cleaner off by
pressing the button (9) and check the liquid
level in the tank (18). If the tank (18) is empty
and you still need to continue cleaning, add
the solution according to the instructions given
in the chapter “Filling the liquid tank with
detergent”.
Liquid collecting mode
•
Before the use, make sure that you followed the
instructions for the liquid collecting mode when
assembling the vacuum cleaner.
•
Pull out the required length of the power cord of
the vacuum cleaner by the plug and connect it
to the mains socket.
Warning: Do not pull out the power cord beyond
the yellow mark on it. Pulling the power cord
beyond the red mark may damage the automatic
cord winding system.
To Next Page
Loading...
