26
•
Disconnect the vacuum cleaner from the mains.
Holding the power plug, press the button (7)
to wind the power cord back into the vacuum
cleaner. Make sure that the cord is fully wound.
•
Press any side of the connector (14) on the
vacuum cleaner body and disconnect the pipe
(13) from the connector (14).
•
Disconnect the flexible hose (6) from the vacu-
um cleaner. Remove all accessories fastened to
the flexible hose (6). Be careful so the remain-
ing water in the hose doesn’t leak on the floor.
Drain the remaining water from the flexible
hose (6).
•
Wash the flexible hose (6) with clean water and
let it dry completely before taking it away for
storage.
•
If you have used the hard floor wet cleaning
attachment (37), remove the rubber squeegee
(38) from it. Wash it and dry.
•
To remove the attachment (37) from the main
wet cleaning attachment (30), press the release
button in the upper part of the attachment (30)
body and at the same time pull the attachment
(37) (pic. H1). Press the release button located
on the left side of the attachment (30) and com-
pletely remove the attachment (37) (pic. H2).
•
The liquid supply pipes can be remove from both
wet cleaning attachments only by disconnecting
them from the spray nozzle tips (pic. H3).
•
Wash all removable accessories intended for
wet cleaning and collecting water under clean
running water and dry completely before taking
them away for storage.
•
Remove dirt such as animal hair, hair etc. from
the removable accessories attached to the tele-
scopic pipe (27) or the flexible hose pipe (26).
You can cut hair wound on the rotary brush (25)
with scissors for easier removal. If necessary,
wipe the accessories with a slightly damp cloth
and then wipe them dry.
•
Do not immerse the vacuum cleaner body into
water or other liquids and do not wash it under
running water.
•
If the outer surface of the vacuum cleaner is
dirty, wipe it with a wet cloth.
•
Make sure that no liquid enters the vacuum
cleaner body.
•
Do not use metal sponges and brushes, sol-
vents or abrasives to clean the vacuum cleaner
surface and accessories.
CARE
Attention! To reduce the risk of fire, electric
shock or personal injury, always unplug the vacu-
um cleaner from the mains before maintenance,
cleaning or troubleshooting.
Inlet filter
•
Open the upper lid (15) of the vacuum cleaner,
remove the receptacle (4) and the liquid tank (18).
•
Open the lid of the inlet filters module in the
base (5) of the vacuum cleaner. To do this, pull
up the clamp in the front part of the lid (pic. I1)
and remove the lid.
•
Take out the first foam filter (pic. I2).
•
Take out the lower HEPA filter, replace it, if nec-
essary (pic. I3).
•
If the filters are clogged, replace them with new
ones or wash them under clean running water
and dry completely at room temperature.
•
Install the clean filters in reverse order and close
the lid.
Note: install only completely dried filters in the
vacuum cleaner.
•
When installing the filters in the vacuum cleaner,
follow their correct sequence.
•
To secure the inlet filters cover, match the
clamp ledges on the back of the cover with
the corresponding grooves in the base of the
vacuum cleaner body. Then press on the inlet
filters cover until the lock clicking (pic. I4).
Outlet filter
•
The outlet filters are fixed on the inside of the
plastic air outlet grid, which is located on the
back of the vacuum cleaner between the wheels
under the carrying handle. To remove the grid,
press the clamp tab and pull it away from the
vacuum cleaner body (pic. J1).
•
Remove the upper and lower porous filters
(pic. J2). If they are clogged, wash them under
clean running water and dry completely at room
temperature. If necessary, replace them with
new ones.
•
Install clean and dry filters into the base of the
plastic grid.
Note: install only completely dried filters in the
vacuum cleaner.
•
Install the plastic air outlet grid with the filters
into the corresponding grooves on the right side
of the vacuum cleaner body. Press on the grid
towards the vacuum cleaner until the clamp tab
distinctive click (pic. J3).
Storage
•
Keep the vacuum cleaner and the accessories
in a dry place at room temperature, away from
children.
Warning: Always pour dirty water from the recep-
tacle (4). You can leave water or cleaning solution
in the tank (18) for further use but no longer than
10 days. Always wash and dry all filters before tak-
ing the vacuum cleaner away for storage.
To Next Page
Loading...
