Vivint VS-KPAD01-001 Quick Reference



Adding the Keypad to the System – Network Inclusion
AddthekeypaddevicetotheVivintsystemusingoneofthefollowingmethods:
ThisproductcanbeoperatedinanyZ‐WavenetworkwithotherZ‐Wavecertifieddevicesfromothermanufacturers.Allmainsoperatednodeswithinthenetworkwillactas
repeatersregardlessofvendortoincreasereliabilityofthenetwork.AS2securityenabledcontrollerisrequiredtooperatetheproduct.

 Vivintapp(SmartStart):ScantheSmartStartQRcodeontheboxwithyoursmartphone,andthenfollowthepromptsintheapp.(Note:
TheQRcodecanalsobefoundinsidethebatterycoverunderthebatteries.)SmartStartenabledproductscanbeaddedintoaZ‐Wave
networkbyscanningtheZ‐WaveQRCodepresentontheproductwithacontrollerprovidingSmartStartinclusion.Nofurtheractionis
requiredandtheSmartStartproductwillbeaddedautomaticallywithin10minutesofbeingswitchedoninthenetworkvicinity.
 Vivintpanel/hubviaZ‐Wave(ClassicInclusion):UsethisstandardmethodforaddingZ‐Wavedevicesatthepanelorhub.Usethe
"PAIR/RESET"buttonnexttothebatterytray.Followtheonscreenpromptstoaddthekeypad.
Installation Instructions
Youcaninstall(mount)thekeypadwitheitherscrewsortape:
1. Tomountwiththeprovidedscrews:
a. Slidethebatterycover/mountingplatedownandremoveit.
b. Placethemountingplateinthedesiredlocation.
c. Securethemountingplatewiththe2screws,usingthe
slotted
holetoadjusttheplateupordowntoensureapreciselevel.
d. Reattachthekeypadbyplacingitdirectlyonthemounting
plate,andslidingitdownuntilitlocksintoplace.
2. Tomountwithtape:
a. Removethetape'sbackingpaperfrombackofthemounting
plate(donotremovetheplateitself).
b. Placethekeypadinthedesiredlocation,beingcarefulto
ensureapreciselevel.
c. Pressthekeypadagainstthewallfor30secondstoactivate
thetapeandsecureittothewall.
3. Onceinstalled,enablethebatteriesbyremoving
thepulltab.
4931N300WProvo,UT84604


TheVivintKeypadisawirelessZ‐Wave
TM
controldevicethatprovidesremote
accesstothesecurityfeaturesforaVivintSmartHome™system,including
enablinganddisablingboththeArmAwayandArmStaysecuritymodes.Thekeypadcanalsobe
usedtotransmitasignaltoVivintMonitoringforfire,panic,
andgeneralemergencyconditionssuch
asahomeintrusion.
Thekeypadhasaneasy‐to‐useinterfacewithidentifiedandilluminatedbuttons,
aswellasindicatoriconsthatshowwhenthedeviceisoffline,orbattery
powerislow.Italsodisplayssecuritysystemstatuswithadowncastlight.
Thisdocumentincludesaproductdescription,installation
instructions,basicoperation,
illustrations,technicalspecifications,andregulatoryreferences.

Basic Operation / User Functionality
Oncethekeypadisupandrunning,theusercanperformthe
followingfunctions.Formoredetails,refertoonlineHelpat
theVivintSupportsite:support.vivint.com.

MAINFEATURES—
 ArmtoSTAYmode(press&holdthebuttonfor3seconds)
 ArmtoAWAYmode(press&holdthebuttonfor3seconds)
 Disarmthesystem(enteravaliduser's4‐digitPINcode)
 SendanemergencysignaltoVivintMonitoring(press
thePANIC,FIRE,or
EMERGENCYbuttonfor2seconds)
 Verifysystemstatus(wakethekeypadbytouchingit,
andviewthedowncastlight)asindicatedbythesecolors:
Green:Systemdisarmed
Orange:Systemarmed
Red:Alarminprogress
QuickReference(UserManual
–
Install&Operation)
Keypad(frontview)—
Vivint Keypad
(VS-KPAD01-001)

Keypad(backview,open;
batterycover/mountingplateoff)—

Vivint VS-KPAD01-001 Specifications

General

Brand	Vivint
Model	VS-KPAD01-001
Category	Keypad
Language	English