This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reects the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE. *1754724_v2_0619_02_hk_m_en
• Connect the micro-USB connector of a micro-USB charging cable (not supplied) to the
micro-USB input (4). Connect the USB-A connector of the USB charging cable to a suitable
USB power source (e.g. USB charger with 2000 mA output current). The charging time is
about 8 - 9 hours.
• You can also charge the internal rechargeable battery via the USB-C
TM
input/output (2)
using the included charging cable (USB-C
TM
/ USB-A) and a PD (power delivery) charger
(not supplied). The charging time is approximately 3 hours with PD 45 W. When charging with
PD, the PD indicator (1) lights up.
• The battery level indicator (5) ashes during charging.
0 – 25 % 25 – 50 % 50 – 75 % 75 – 99 % 100 %
LED 1 Flashes blue Solid blue Solid blue Solid blue Solid blue
LED 2 Off Flashes blue Solid blue Solid blue Solid blue
LED 3 Off Off Flashes blue Solid blue Solid blue
LED 4 Off Off Off Flashes blue Solid blue
LED 1 is located directly next to the function switch. LED 4 is located on the outside.
• Once the internal rechargeable battery is fully charged, all 4 LEDs will light up.
• Disconnect the cable from the product and the power source as soon as the internal
rechargeable battery is fully charged. The product is ready for use.
If you only use the product occasionally, we recommend that you fully charge the
internal rechargeable battery every 3 months in order to retain maximum capacity.
Charging mobile devices
• Connect your mobile device to the USB-C
TM
input/output (2) or to the USB-A output (3). You
can also load two devices on both ports at the same time.
The charging currents of the USB outputs can be found in “Technical data”. Check
the charging current of your mobile device.
The internal rechargeable battery must be sufciently charged to charge two devices
at the same time.
• A fast charge is possible via the USB-C
TM
input/output (2). Devices with different voltages
(5 V, 9 V, 12 V, 15 V, 20 V) can be charged via this connection.
• The charge indicator lights solidly during charging and indicates the current state of charge
of the power bank.
• If the charging process does not start automatically, press the function switch (6) to turn on
the product.
• Monitor the charging process. Disconnect the USB cable from the product and the mobile
device as soon as the charging process is completed.
Troubleshooting
Problem Cause Solution
Mobile device cannot
be charged.
Rechargeable battery is
discharged.
Function switch was not
pressed.
The product may take longer
to start charging on some
mobile devices.
Charge the internal
rechargeable battery of the
product.
Press the function switch.
Wait up to about 20 seconds.
The charging of the
internal rechargeable
battery was
interrupted.
Incompatible charging cable
used.
Bad contact at the USB input/
output.
The product is not in a stable
position.
Use the included charging
cable.
Disconnect the USB plug and
connect it again.
Ensure adequate stability
during charging. Avoid
movement and vibration.
LEDs light up even
though the charging
cable is disconnected.
LEDs glow for a while after
the charging cable has been
disconnected.
LEDs will go off automatically
after approx. 15 seconds.
Care and Cleaning
• Disconnect the product from all the connected devices before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the housing or cause the product to malfunction.
• This product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
• Use a lint-free cloth to clean the product. Do not press too hard on the housing, as this can
lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus full your statutory obligations and contribute to environmental protection.
Technical Data
Input voltage/current ..................... Micro-USB: 5 V/DC 2.4 A
USB-C
TM
: PD 5 – 20 V/DC (45 W max.)
Output voltage/current .................. USB-A: 5 V/DC 3 A, 9 V/DC 2 A
USB-C
TM
: PD 5 – 20 V/DC (45 W max.)
Combined USB-A and USB-C
TM
max. 45 W
Rechargeable battery ................... Li-Ion, 20100 mAh 72.96 Wh
(rechargeable battery type 18650)
Operating/storage Conditions ....... 0 to +40 ºC, <85% RH (non-condensing)
Dimensions (L x W x H) ................ 162 x 79 x 23 mm
Weight .......................................... 377 g
To Next Page
Loading...
Need help?
General
