Volvo EC200D - Page 194

N
N
O
O
T
T
E
E
!
!
Protect electrical leads in an appropriate way and
be careful not to damage the cab prefilter when
cleaning the machine.
NOTICE
D
D
o
o
n
n
o
o
t
t
s
s
p
p
r
r
a
a
y
y
w
w
i
i
t
t
h
h
h
h
i
i
g
g
h
h
p
p
r
r
e
e
s
s
s
s
u
u
r
r
e
e
i
i
n
n
t
t
o
o
t
t
h
h
e
e
s
s
e
e
a
a
l
l
i
i
n
n
g
g
o
o
f
f
t
t
h
h
e
e
s
s
l
l
e
e
w
w
i
i
n
n
g
g
r
r
i
i
n
n
g
g
,
,
t
t
h
h
e
e
w
w
a
a
t
t
e
e
r
r
m
m
a
a
y
y
p
p
e
e
n
n
e
e
t
t
r
r
a
a
t
t
e
e
a
a
n
n
d
d
a
a
f
f
f
f
e
e
c
c
t
t
t
t
h
h
e
e
c
c
h
h
a
a
r
r
a
a
c
c
t
t
e
e
r
r
i
i
s
s
t
t
i
i
c
c
s
s
o
o
f
f
t
t
h
h
e
e
g
g
r
r
e
e
a
a
s
s
e
e
.
.
- Use a soft sponge.
- Finish by rinsing the whole machine with only
water.
- Always lubricate the machine after washing.
- Touch-up the paint finish when required.
P
P
a
a
i
i
n
n
t
t
f
f
i
i
n
n
i
i
s
s
h
h
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
- Machines which are used in corrosive
environment suffer more from rust than others. As
a preventive measure it is recommended that the
paint finish should be maintained every sixth
months.
- At first clean the machine.
- Apply Dinol 77B (or corresponding transparent
waxy anti-rust agent) at a thickness of 70-80 μ.
- A protective layer of underseal Dinitrol 447 (or
corresponding) may be applied under the
mudguards where mechanical wear is expected.
T
T
o
o
u
u
c
c
h
h
-
-
u
u
p
p
p
p
a
a
i
i
n
n
t
t
i
i
n
n
g
g
- Check if there are any damaged areas of the paint
finish.
- At first clean the machine.
- Rectify any damage to paint finish in a
professional way.
1
1
9
9
2
2
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
s
s
e
e
r
r
v
v
i
i
c
c
e
e
,
,
w
w
h
h
e
e
n
n
r
r
e
e
q
q
u
u
i
i
r
r
e
e
d
d