VonHaus 3500160 - User Manual

A5P | 01
3500160
Please read all instructions carefully before use and
retain for future reference.
Veuillez lire attentivement ces instructions avant
utilisation et conservez-les pour pouvoir les consulter
à l’avenir.
Bitte lesen Sie die Anleitung sorgfältig und bewahren Sie
sie als Referenz auf.
Leed todas las instrucciones detenidamente antes de
usar y retened para futuras consultas.
Si prega di leggere attentamente tutte le istruzioni prima
dell’uso e conservarle per una futura consultazione.
Lea todas las instrucciones detenidamente antes de
usar y consérvelas para futuras consultas.
CAUTION Do not immerse in water.
ATTENTION Ne pas immerger dans l’eau.
VORSICHT Nicht in Wasser tauchen.
PRECAUCIÓN No sumergid en agua.
AVVERTENZA Non immergere nell’acqua.
PRECAUCIÓN No sumergir en agua.
CAUTION Do not look into the beam.
ATTENTION Ne regarde pas dans le rayon.
VORSICHT Schauen Sie nicht in den Strahl.
PRECAUCIÓN No mires dentro de la viga.
AVVERTENZA Non guardare nel raggio.
PRECAUCIÓN No mire en el rayo.
Protect your eyes.
Protégez vos yeux.
Schützen Sie Ihre Augen.
Protejed sus ojos.
Proteggere gli occhi.
Proteja sus ojos.
Protect your ears.
Protégez vos oreilles.
Schützen Sie Ihre Ohren.
Protejed vuestros oídos.
Proteggere le orecchie.
Proteje sus oídos.
Protect your hands.
Protégez vos mains.
Schützen Sie Ihre Hände.
Protejed vuestras manos.
Proteggere le mani.
Proteja sus manos.
Wear a dust mask
Portez un masque anti-poussière
Tragen Sie eine Staubmaske
Usad una máscara de polvo
Indossare una mascherina antipolvere
Usa una máscara de polvo

Summary

General Safety Precautions

Personal Protective Equipment Warnings

Protect your eyes. Protect your ears. Protect your hands. Wear a dust mask.

Laser Beam Warning

CAUTION Do not look into the beam.

Safety Features and Disconnection

Thermal Cut-Out Operation

This appliance has a thermal cut out switch. The thermal cut out will activate and shut down the appliance should the appliance overheat.

Disconnection for Maintenance

Disconnect appliance from mains before cleaning, maintenance or after a thermal cut out event.

Product Usage and Safety Guidelines

Intended Use

Only operate the power tool/machine for its intended purpose and within the parameters specified.

Key Safety Warnings

Avoid body contact with earthed surfaces, do not operate in explosive atmospheres, always wear eye protection, stay alert, use PPE.

Work Area Safety

Keep work area clean and well lit. Keep children and bystanders away.

General Tool Use and Care

Do not force the tool. Ensure switch works. Disconnect before adjustments. Store properly. Maintain tool.

Cleaning & Maintenance

Never soak electrical components. Disconnect before cleaning. Ensure motor stops before maintenance.

Table Saw Operation and Safety

Table Saw Operation Warnings

Keep guards in place. Guards must be in working order and be properly mounted.

Kickback Causes and Related Warnings

Never stand directly in line with the sawblade always position your body on the same side of the saw blade as the fence.

Technical Specification

Rated Voltage 230-240V ~, Rated Power 2000W, Rated Frequency 50Hz

Adjustments and Setup

Bench Mounting

The tool is equipped with 4 holes to facilitate bench mounting. Use 4 bolts (not supplied) to secure the tool.

Dust Collection

Attach the Dust Collection Bag (11) to the Dust Exhaust (10) before use to reduce dust during operation.

Before First Use Setup

Confirming 90° Angle

To confirm the 90° Angle: 1. Make sure that the Power Cable is removed.

Confirming 0° Rotary Table Setting

To confirm the 0° Rotary Table Setting: 1. Push the Saw Arm (3) down to its lowest position...

Setting Cutting Depth

Adjusting Depth of Cut

The depth of cut can be pre-set for even and repetitive shallow cuts.

Cross Cut Procedure

Performing a Cross Cut

If possible, always use a clamping device such as the Clamp Adjusters to secure your workpiece.

Bevel Cut Procedure

Performing a Bevel Cut

A bevel cut is made by cutting across the grain of the workpiece with the Blade angled to the Fence...

Compound Mitre Cut Procedure

Performing a Compound Mitre Cut

A compound mitre cut involves using a mitre angle and a bevel angle at the same time.

Saw Operation

Turning the Saw On

To turn on the Saw, move the Switch Lock to the left before depressing and holding the Switch Trigger (19).

Turning the Saw Off

To turn the Saw off, simply release the Switch Trigger (19).

Changing the Saw Blade

Blade Replacement Steps

1. Pull the Release Handle (4) and lift to positon the Saw Blade.

Lubrication and Reassembly

Wipe a drop of oil onto the Inner Blade Washer and the Outer Blade Washer where they contact the Saw Blade.

Maintenance Procedures

Cleaning Precautions

CAUTION: Wear safety glasses and a mask for protection whilst cleaning the Mitre Saw.

General Cleaning and Lubrication

For optimum use, regularly check to see if any dust or foreign matter has entered the ventilation slots...

Product Information and Support

Disposal Information

Please recycle where facilities exist.

Customer Service and Warranty

If you are having difficulty using this product and require support, please contact hello@domu.co.uk (UK/EU)

Copyright Notice

All material in this instruction manual are copyrighted by DOMU Brands.

VonHaus 3500160 Specifications

General

Type	Circular Saw
Power Source	Corded Electric
Blade Diameter	190mm
No Load Speed	5500 RPM
Max Cutting Depth at 90°	65 mm
Max Cutting Depth at 45°	44 mm