VRG Controls RCVC 3000 User Manual

VRG CONTROLS LLC. 14 of 39 MAY 2021
RCVC 3000 - Red Circle Valve Controller
Installation, Operation, Maintenance Manual
Open Programming Connection to RCVC
1. Ensure that the RCVC App is installed on the
c o m p u t e r a n d t h e U S B d r i v e r s h a v e b e e n
installed. To install USB drivers, connect the USB
to the computer and the drivers will install
automatically if there is an internet connection.
2. Open the RCVC App and ensure there is 24VDC
power to the RCVC.
3. Verify the USB is connected to the computer and
select DEVICE from the menu. Click on detect
device to ensure the RCVC App can
communicate to the RCVC. Once a connection is
established click on Device and select Connect
to device.
4. The program will automatically load the setup
le from the RCVC into the program. A window
will appear asking for a folder name and a le
name. For the folder name it is recommended
to put the station name. For the le name it is
recommended to put the job number, this way it
is easier to keep the les organized.
Eliminate Excessive COM PORTS
on Computer
When attempting to Open Programming Connection to
RCVC using the Setup Application operator may experience
di󰀩culty establishing a COM PORT. It may be necessary to
remove excessive COM PORTS on your Windows
TM
operating system.
1. Click Windows Button on Computer.
2. Type “Device Manager” and Select.
3. Click View, Show Hidden Devices.
4. Click Ports (COM & LPT)
5. Select any “Gray” COM Port and Click red “X” at
top of Window or DELETE.
6. Select uninstall when prompted “Do you want to
uninstall this connection?”
Read and Write Setup File from Controller
1. When connecting to the device the program will
automatically read the setup le. This can be
found under the Online tab on the left side of the
window. You can expand the online tab to see
the folder and le associated with the device.
2. To write a le to the device, right click on the le
name under the online section. Select Load
Standard File and then select the desired le
from the drop-down menu. Click OK to accept
the le and then select Yes to conrm you want to
overwrite the current le.
3. Once complete a message will appear saying
“Write setup le successful-clearing memory.”
Once the memory has been cleared a new
window will pop up letting you know this has
nished. Once complete, select device and
connect to device to reconnect.
Determining Setup le version in the
RCVC App
1. Open RCVC app software
2. Connect to the RCVC Via the USB connection
3. Once connected to the device Assign a project
and le name.
4. In the top information box the Application number
(VRG.4.24.4-2) will display the current setup le version.
VRG.4.24.4-1 for the old version and VRG.4.24.4-2 for the
new version.
Determining Setup le version On the RCVC
Controller
1. Short push the navigation wheel to go into manual mode.
2. Long push the navigation wheel to go into the menu.
3. Scroll down to Settings and short push to select.
4. Scroll to About and short push to select
5. Next to App Revision will be the setup le version num-
ber. VRG.4.24.4-1 for the old version and VRG.4.24.4-2 for
the new version.
New RCVC software setup le upgrade
1. Open RCVC app software
2. Connect to the RCVC Via the USB connection
3. Once connected to the device Assign a project and le
name.
4. Select the setup tab followed by the analog input tab.
5. Copy the calibration values for Feedback, Command and
Retransmission.

VRG Controls RCVC 3000 Specifications

General

Brand	VRG Controls
Model	RCVC 3000
Category	Controller
Language	English