What to do if my Vulcan-Hart GR Fryer has no power and display not lit?
If your Vulcan-Hart Fryer has no power to the cooking control and the display is not lit, causing it not to heat, check if the power switch is off or malfunctioning. Also, inspect the main circuit breaker to ensure it's not off. A faulty transformer or malfunctioning interconnecting wiring could also be the cause.
Why won't my Vulcan-Hart GR gas burners maintain flame?
If your Vulcan-Hart Fryer gas burners ignite but won't maintain a flame, it could be due to incorrect gas pressure, an obstructed or incorrect gas orifice, a burner malfunction, or a gas pilot malfunction.
Why is my Vulcan-Hart Fryer heat excessive or low?
If your Vulcan-Hart Fryer experiences excessive or low heat, it may be due to an incorrect temperature offset selected, a malfunctioning temperature probe, incorrect gas pressure, an obstructed or incorrect gas orifice, a cooking control malfunction, or an interface board malfunction.
Why is the high limit thermostat shutting off gas burners on my Vulcan-Hart GR?
If your Vulcan-Hart Fryer's high limit thermostat is shutting off the gas burners, the shortening level may be below the minimum fill line, or there could be a probe, cooking control, interface board, or high limit thermostat malfunction.
What to do if Vulcan-Hart GR sparks but gas doesn't ignite?
If your Vulcan-Hart Fryer sparks but the gas does not ignite and the display is lit, the gas combination valve might be off or inoperative, the manual gas valve might be closed, the gas supply could be off or have insufficient pressure, the high limit thermostat might be open, there may be an interconnecting wiring malfunction, or the ignition module could be malfunctioning.
Why isn't the pump motor running to discard shortening in my Vulcan-Hart GR?
If your Vulcan-Hart Fryer's pump motor isn't running to discard shortening and the display is lit, ensure the filter key on the control panel is pressed and held long enough (default 3 seconds). Also, check if the discard handle (white) is extended. A malfunctioning R1 pump motor relay, cooking control, interface board, interconnecting wiring, or the pump motor itself could also be the cause.
Why isn't the pump motor circulating shortening in my Vulcan-Hart GR?
If your Vulcan-Hart Fryer's pump motor is not running to circulate shortening through the filtering system, even though the display is lit, it might be because the filter key on the control panel wasn't pressed or held long enough (default is 3 seconds). Other potential causes include a malfunctioning R1 pump motor relay, cooking control, interface board, interconnecting wiring, or the pump motor itself.
What to do if Vulcan-Hart GR Fryer shortening not discarding but pump motor is on?
If your Vulcan-Hart Fryer's shortening is not discarding, but the pump motor is running, the filter screen might be plugged, there could be a clog in the filter system lines, the shortening might be too thick because it's below 300°F, the discard valve switch may be malfunctioning, the R2 fill relay could be malfunctioning, there might be a discard valve mechanical malfunction, the discard hose connection might not be fully engaged, or the pump could be inoperative.
What to do if Vulcan-Hart Fryer shortening not filtering but pump motor is on?
If your Vulcan-Hart Fryer shortening is not filtering, but the pump motor is on, the filter screen may be plugged, there could be a clog in the filter system lines, the shortening might be too thick because it's below 300°F, the R2 fill relay might be malfunctioning, the fill solenoid valve could be malfunctioning, there may be an interconnecting wiring malfunction, or the pump could be inoperative.
Why does my Vulcan-Hart GR take so long to melt shortening?
If your Vulcan-Hart Fryer takes an excessive amount of time to melt shortening (more than 45 minutes), the melt cycle timing might be incorrect, there could be insufficient gas pressure, the gas orifice might be plugged or obstructed, the probe could be malfunctioning, the cooking control might be malfunctioning, or the interface board could be malfunctioning.
General| Oil Capacity | Varies by model (e.g., GR45: 45-50 lbs, GR65: 65-75 lbs) |
|---|---|
| Weight | Varies by model |
| Series | GR |
| Fuel Type | Gas |
| Construction | Stainless steel |
| Dimensions | Varies by model |
| Capacity | Varies by model |
To Next Page
