W&T 58631 - User Manual

To Next Page

Manual

Com-Server Highspeed

Release 2.10, October 2006

Type 58631, 58641,

58633, 58031,

58034, 58231,

58431, 58432,

58331, 58334

Com-Server Firmware 1.52 or higher

W&T

Main Page

Default Chapter4
- Table of Contents4
1 Quickstart9
- Flow Chart - Network Installation Using Wutility10
- Overview of Configuration Menu11
- Factory Default Settings12
2 Assigning the IP Address13
- Configuring Network Parameters with Wutility14
- Assigning the IP Using the ARP Command18
- Serial Assigning of IP, Subnet Mask and Gateway20
- Assigning the IP Using DHCP Protocol24
- Assigning the IP Using BOOTP Protocol28
- Assigning the IP Using a RARP Server30
3 Form Factors31
- Com-Server Highspeed Industry32
- Com.server Highspeed Isolated 5863333
- Com-Server Highspeed Office34
- Com-Server Highspeed 1935
- Com-Server Highspeed OEM 5843136
- Com-Server Highspeed Compact 5823137
4 Supply Voltage39
- Com-Server Highspeed Industry and Isolated40
- Com-Server Highspeed Industry 58631/UL41
- Com-Server Highspeed Industry Poe42
- Com-Server Highspeed Office43
- Com-Server OEM and Compact44
- Com-Server Highpeed 1945
5 Interfaces and Displays47
- Ethernet Connection48
- RS232/422/485 Combi-Module50
- Opening the Com-Server50
- Mode Selection51
- RS232 Mode (Factory Default)51
- RS422/485 Mode53
- Interface for the OEM-Com-Server 5843156
- Option: 20Ma Interface58
- Interfaces for the OEM-Com-Server 5843260
- LED Displays63
6 Configuration Access to the Com-Server65
- Configuration Menu Structure66
- Configuration Via Telnet68
- Configuration Via Browser - Web Based Management71
- Activating WBM with the Wutility-Tool71
7 The Basis Configuration of the Com-Server77
- Saving Your Settings78
- Menu: INFO System79
- Menu: SETUP System80
- Menu: SETUP System R Setup TCP/IP80
- Menu: SETUP System R Telnet Password83
- Menu: SETUP System R System Password84
- Menu: SETUP System R System Name85
- Menu: SETUP System R Flash Update85
- Menu: SETUP System R Factory Defaults86
- Menu: SETUP System R Reset86
- Menu87
8 Configuration of the Serial Port89
- The Serial Parameters (Menu: UART Setup)90
- Baud Rate, Data Bits, Stop Bits, Parity90
- The Handshake Modes91
- FIFO Send/Rec96
9 The Protocol Stack of the Com-Server97
- Services of the Com-Server98
- Addressing in the TCP/IP Network99
- The Protocol Stack of the Com-Server100
- Data Transfer Per TCP/IP and UDP/IP Sockets100
10 Data Transfer Per TCP/IP Sockets103
- The Com-Server as TCP Server104
- Configuration of the Local Port Number104
- Optional Settings105
- The Com-Server as TCP-Client107
- TCP Client Mode with Fixed Destination System108
- TCP Client Mode with Serial Addressing111
- Optional Settings112
- Deactivating TCP Client Mode114
- Application114
- Client/Server Mode between Com-Server-Ports114
11 Data Transfer Per UDP117
- The Com-Server as UDP Peer118
- Setting the Local UDP Port Number119
- UDP Clientmode with Fixed Destination System120
- UDP Client Mode with Serial Addressing121
- Optional Settings123
- Deactivating UDP Mode124
12 The Windows COM Port Redirector125
- Virtual COM Ports126
13 Box-To-Box Mode129
- Box-To-Box Mode130
- Configuring Box-To-Box Mode131
- Optional Settings132
- Deactivating Box-To-Box Mode132
14 Data Transfer Per FTP135
- The Com-Server as FTP Server136
- The Com-Server as FTP Client138
- Configuring the Destination Address and Port no138
- Deactivating FTP Client Mode145
- Application Examples145
15 Data Transfer Per Telnet147
- Com-Server as Telnet Server148
- The Com-Server as Telnet Client149
- Optional Settings151
- Deactivating Telnet Client Mode151
16 IP Bus Mode154
- Function of the IP Bus Mode154
- Configuring the IP Bus Mode155
- Deactivating IP Bus Mode156
17 The Com-Server as SLIP Router157
- Configuring the SLIP Mode158
18 Serial Socket Interface163
- Serial Socket Interface164
19 Status and Error Messages165
- Menu Setup Port X R Port State166
20 Expanded Services of the Com-Server169
- The Control Port170
- Reset Com-Server-Port178
- Software Reset of the Com-Server180
- Uploading/Downloading Configuration Data181
- Inventory Taking Per UDP/8513183
- SNMP Management186
21 Firmware Update of the Com-Server187
- Where Do I Get the Current Firmware188
- Network Firmware Update under Windows189
- Network Firmware Update under UNIX190
Appendix193
- TCP/IP under Windows 9X194
- TCP/IP under Windows NT195
- Used Ports and Network Security196
- Serial Assignment of the IP Address under Windows200
- Web Application HTTP, SMTP, POP3204
- Wutility - Inventory and Management Tool206
- Hardware Reset to Factory Defaults207
- Technical Data208
- Declaration of Conformity215
Index216

Need help?

Do you have a question about the W&T 58631 and is the answer not in the manual?

W&T 58631 Specifications

General

Brand	W&T
Model	58631
Category	Control Unit
Language	English

W&T 58631 - User Manual

Table of Contents

W&T 58631 Specifications