WAREMA WMS Hand-held transmitter plus User Manual

Operating and installation instructions
WAREMA Mobile System
WMS Hand-held transmitter plus
Keep for future use!
Valid from 01 April 2017
2018148_a•en•2017-04-01
We reserve the right to make technical changes
1
Safety instructions
AUTIONC
The WMS Hand-held transmitter plus is for
indoor use only. It is not water-proof. Do not
leave the WMS Hand-held transmitter plus
outdoors.
AUTIONC
Never activate buttons on your WMS Hand-
held transmitter plus arbitrarily without a line
of sight to the sun shading system. Chil-
dren must not play with this product – keep
remote controls and transmitters out of the
reach of children!
Follow the steps below in the order shown to ensure
problem-free operation:
 Please read these instructions carefully.
 Insert the batteries.
 Learn the WMS Hand-held transmitter plus into the
receivers.
 Check that the unit is functioning correctly.
Installation
As it is a hand-held transmitter, the WMS Hand-held trans-
mitter plus does not require installation.
Battery compartment



Fig. 2 Battery compartment of the WMS Hand-held transmitter
plus
Pos. Fig. Function
1
Batteries
The WMS Hand-held transmitter plus requires two
batteries of type AAA (IEC LR03, "Micro").
2
Learn button
Activates or closes the learn mode of the WMS
Hand-held transmitter plus
3
L LED
Indicates that the WMS Hand-held transmitter plus
is in learn mode (lights up green)
General information
Fig. 1 WMS Hand-held transmitter plus
The WAREMA Mobile System (WMS) Hand-held trans-
mitter plus is used for the remote control of WAREMA
WMS receivers. The receiver sends a confirmation of the
received commands, and the WMS Hand-held transmitter
plus indicates that it received the confirmation.
The WMS Hand-held transmitter plus supports five differ-
ent product types (awning, roller shutter, external venetian
blind, window, light).
Only one receiver or one group with multiple receivers of
the same product type can be actuated at any one time
per channel (6 channels).
The comfort control functions can be switched on and off
by channel via the WMS Hand-held transmitter plus.
A WMS Hand-held transmitter, a WMS Central transmitter
or the WMS studio software is needed for commissioning
a weather station.
If a control function is preventing operation of the product
(e.g. a wind alarm), this is also displayed on the WMS
Hand-held transmitter plus.
Intended use
The WMS Hand-held transmitter plus was developed to
control WAREMA Mobile System (WMS) receivers. Any
use other than the purpose described in these instructions
requires approval from the manufacturer.

WAREMA WMS Hand-held transmitter plus Specifications

General

Type	Hand-held transmitter
Frequency	868.3 MHz
Power Supply	Battery
Dimensions	48 mm x 145 mm x 23 mm
Battery	2 x AAA
Range	Up to 100 meters
Battery Type	AAA
Battery Life	up to 2 years

Summary

General Information

Intended Use

Describes the purpose of the WMS Hand-held transmitter plus for controlling WAREMA Mobile System receivers.

Safety Instructions

Important Safety Precautions

Highlights critical safety advice for indoor use and child safety regarding the WMS Hand-held transmitter plus.

Installation

Battery Compartment Details

Details the battery compartment of the WMS Hand-held transmitter plus, including battery type and compartment features.

Operating Elements and Displays

Controls and Indicators Overview

Explains the functions of buttons, LEDs, and displays on the WMS Hand-held transmitter plus.

Operation

Operating the Products

Details how to operate the products using the WMS Hand-held transmitter plus, including channel selection and command transmission.

Learning and Recalling Comfort Positions

Comfort Position Management

Guides on saving and recalling specific comfort positions for connected receivers using the WMS Hand-held transmitter plus.

Switching Comfort Control Functions

Commissioning

Adding to Existing Network

Details the process of adding a WMS Hand-held transmitter plus to an existing network, likely for initial setup.

Example 2: Integration with WMS Central Transmitter

Integrating with WMS Central Transmitter

Guides for expanding a system with a WMS Central transmitter by adding a WMS Hand-held transmitter plus.

Example 3: Integrating Another WMS Hand-held Transmitter Plus

Integrating Another WMS Hand-held Transmitter Plus

Instructions for expanding a system by adding a second WMS Hand-held transmitter plus and copying channels.

Example 4: Integrating a WMS Hand-held Transmitter

Integrating a WMS Hand-held Transmitter

Guides for integrating a standard WMS Hand-held transmitter into a network via a WMS Hand-held transmitter plus.

Example 5: Learning into New Receivers

Learning into New Receivers

Procedure for learning the WMS Hand-held transmitter plus into new receivers, including plug receivers and actuators.

Example 6: Deleting Learned-in Products

Deleting Learned-in Products

Instructions for removing learned-in products from the WMS Hand-held transmitter plus and the network.

Maintenance and Cleaning

Replacing Batteries

Instructions for replacing the batteries in the WMS Hand-held transmitter plus when the transmission LED indicates low power.

Cleaning the Housing

Guidance on how to clean the housing of the WMS Hand-held transmitter plus using suitable materials.

Liability and Disposal

Disposal Information

Guidance on the proper disposal of the device and batteries according to legal regulations.

Technical Data

Technical Specifications

Details key technical specifications for the WMS Hand-held transmitter plus, including supply, RF transceiver, and housing.

Ambient Conditions and Article Numbers

Provides information on operating and storage conditions, humidity, and article numbers for the WMS Hand-held transmitter plus.