WARRIOR 58089 - Kickback and Related Warnings; Understanding and Preventing Kickback; Safety Warnings Specific for Grinding Operations; Grinding Operation Safety

Page 7For technical questions, please call 1-888-866-5797.Item 58089
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging
causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power
tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
1. Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
7KHRSHUDWRUFDQFRQWUROWRUTXHUHDFWLRQVRU
NLFNEDFNIRUFHVLISURSHUSUHFDXWLRQVDUHWDNHQ
2. Never place your hand near the rotating
accessory.$FFHVVRU\PD\NLFNEDFN
over your hand.
3. Do not position your body in the area where
power tool will move if kickback occurs.
.LFNEDFNZLOOSURSHOWKHWRROLQGLUHFWLRQRSSRVLWH
WRWKHZKHHO¶VPRYHPHQWDWWKHSRLQWRIVQDJJLQJ
4. Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.&RUQHUVVKDUSHGJHVRUERXQFLQJ
have a tendency to snag the rotating accessory
DQGFDXVHORVVRIFRQWURORUNLFNEDFN
5. Do not attach a saw chain woodcarving
blade or toothed saw blade.6XFKEODGHV
FUHDWHIUHTXHQWNLFNEDFNDQGORVVRIFRQWURO
Safety Warnings Specific for Grinding Operations
1. Use only wheel types that are recommended
for your power tool and the specific
guard designed for the selected wheel.
:KHHOVIRUZKLFKWKHSRZHUWRROZDVQRWGHVLJQHG
FDQQRWEHDGHTXDWHO\JXDUGHGDQGDUHXQVDIH
2. The guard must be securely attached
to the power tool and positioned for
maximum safety, so the least amount of
wheel is exposed towards the operator.
7KHJXDUGKHOSVWRSURWHFWRSHUDWRUIURPEURNHQ
wheel fragments and accidental contact with wheel.
3. Wheels must be used only for recommended
applications. For example: do not grind with
the side of the wheel. Grinding wheels are
LQWHQGHGIRUSHULSKHUDOJULQGLQJVLGHIRUFHVDSSOLHG
to these wheels may cause them to shatter.
4. Always use undamaged wheel flanges that are
of correct size and shape for your selected
wheel. 3URSHUZKHHOIODQJHVVXSSRUWWKHZKHHO
WKXVUHGXFLQJWKHSRVVLELOLW\RIZKHHOEUHDNDJH
5. Do not use worn down wheels from larger
power tools. Wheel intended for larger
SRZHUWRROLVQRWVXLWDEOHIRUWKHKLJKHU
VSHHGRIDVPDOOHUWRRODQGPD\EXUVW
6. Dress appropriately. Wear leather leggings
and fire resistant footwear during use. Do
QRWZHDUSDQWVZLWKFXIIVVKLUWVZLWKRSHQ
SRFNHWVRUDQ\FORWKLQJWKDWFDQFDWFK
DQGKROGPROWHQPHWDORUVSDUNV
Safety Warnings Specific for Sanding Operations
Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommendations
when selecting sanding paper./DUJHUVDQGLQJSDSHUH[WHQGLQJEH\RQGWKHVDQGLQJSDG
SUHVHQWVDODFHUDWLRQKD]DUGDQGPD\FDXVHVQDJJLQJWHDULQJRIWKHGLVFRUNLFNEDFN
SAFETYOPERATIONMAINTENANCE SETUP