Water Boss PROPLUS380 - User Manual

M
M
O
O
D
D
E
E
L
L
S
S
P
P
R
R
O
O
1
1
8
8
0
0
A
A
N
N
D
D
P
P
R
R
O
O
P
P
L
L
U
U
S
S
3
3
8
8
0
0
O
O
W
W
N
N
E
E
R
R
’
’
S
S
M
M
A
A
N
N
U
U
A
A
L
L
A
A
N
N
D
D
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
G
G
U
U
I
I
D
D
E
E
V
V
E
E
R
R
S
S
I
I
O
O
N
N
1
1
.
.
0
0
—
—
T
T
W
W
O
O
-
-
B
B
U
U
T
T
T
T
O
O
N
N

Summary

10 Year Limited Warranty

To Whom Warranty Is Extended

Specifies eligibility and registration requirements for the warranty coverage.

Coverage

Outlines what the limited warranty covers for materials and workmanship.

Warrantors Performance and Length of Limited Warranty

Details repair/replacement terms for different parts and their duration.

Further Exclusions and Limitations on Warranty

Lists conditions and causes not covered by the warranty.

Claims Procedures

Provides instructions on how to report defects and initiate a warranty claim.

General Information

For Owners Reference

Provides contact information and advice for using the manual as a service log.

Getting Maximum Efficiency From the Appliance

Checklist Before Installation

Precautions

Installation Steps and Start-Up Procedures

Step 1 Prepare the Placement Area

Details site preparation, cleaning, and initial checks before installation.

Step 2 Turn Off Water Supply

Instructs on shutting off water and depressurizing lines.

Step 3 Connect Water Lines

Guides on attaching inlet and outlet water connections to the appliance.

Step 4 Connect Gravity Overflow Connection

Explains how to connect the overflow line for safety.

Step 5 Connect Drain Line

Describes how to connect the drain line for backwash water removal.

Step 6 Flush Lines

Instructs on flushing plumbing after installation to remove debris.

Step 7 Check for Leaks

Details procedures for inspecting all connections for water leaks.

Step 8 Plug in the Transformer

Guides on connecting the power supply to the controller.

Step 9 Set Up the Controller

Directs users to the section for programming the appliance's controller.

Step 10 Add Water to the Brine Cabinet

Explains the initial water addition to the brine cabinet.

Step 11 Fill the Brine Cabinet With Salt

Provides instructions for adding salt to the brine cabinet.

Step 12 Complete the Installation

Covers final checks and start-up procedures before normal operation.

Bypass Valve

Two-Button Controller

Setting the Controller

Step 1 Determine the Controller Setting Number

Guides on calculating the correct setting based on water test results.

Step 2 Enter Your Setting Number Into the Controller

Details the procedure for inputting the calculated setting into the controller.

Advanced Customer Settings

Step 1 Set Salt Setting

Allows selection of salt dosage efficiency modes (S1, S2, SA).

Step 2 Set Time of Day

Guides on setting the current time on the controller using a 24-hour clock.

Step 3 Set Time of Regeneration

Allows programming the preferred time for automatic regeneration cycles.

Step 4 Set Demand or Delayed Mode

Configures the regeneration trigger (immediate demand or scheduled delay).

Step 5 Set 96-Hour Mode

Enables a mode to prevent exceeding 4 days without regeneration.

Step 6 Set powerClean Mode

Activates a special mode for cleaning the resin bed with frequent regeneration.

Additional Features

Step 1 Accessing Additional Features

Explains how to enter the special features menu on the controller.

Step 2 Set Units

Allows switching between English (gallons) and metric (liters) units.

Step 3 Restore Factory Defaults

Guides on resetting all controller settings to their original factory configurations.

Cabinet and Assemblies

Troubleshooting

Specifications

Efficiency Statements

Water Boss PROPLUS380 Specifications

General

Voltage	120V
Capacity	38000 grains
Regeneration	Automatic
Water Capacity	Unknown
Cooling Capacity	Unknown
Heating Capacity	Unknown
Power Consumption	Unknown