9
HOW TO USE HELLO BIDET
1) Using dry hands for a beer grip, insert the quick
connector (B) to the special lter holder (A1 -A2)
or Addy (O) turning counterclockwise (g. 6a - 6b);
2) Turn on the faucet, press the lever (F) and adjust
the temperature of the water that comes out of
the handshower (E) by checking it with your hand
(g. 7). Regarding water temperature, keep in mind
that the skin sensivity of inmate areas is always
higher compared to the sensivity of hands; Never
use with water above 38°C/100°F.
3) Sit on the toilet, posion the handshower (E)
between your legs and press the lever (F) in order
to begin the cleansing of your inmate areas (g.
8); the lever (F) will allow you to interrupt the
water ow at any me by simply releasing the
lever.
4) When you are nished, release the lever (F) and
turn o the water from the faucet;
5) Unplug the quick connector (B) from the faucet
lter by turning clockwise;
6) At the end of each cleansing, aer having rinsed
out the bidet handshower (g. 10), blow air into
the aachment connector part (B) in order to get
rid of any remaining water le in the tube (g. 11)
and by simultaneously pressing the control (F) of
the bidet handshower (E).
FREQUENCY AND DURATION OF CLEANSINGS
• The cleansing of your inmate areas with Hello
Bidet can be performed as oen as you like, even
several mes a day;
• The total duraon of a cleansing is absolutely up to
your personal desires.
MAINTENANCE AND STORAGE
• Before use, connect Hello Bidet to the faucet and let
the water run for about 20-30 seconds unl it exits the
handshower;
• Between uses, we recommend keeping the product
thoroughly clean, dry and stored inside its carrying
case;
• When cleaning the product, do not use harsh
detergents so as to avoid damaging the rubber or
plasc parts.
UNIVERSAL ADAPTER ADDY
Included only with Hello Bidet “Travel” version. It can
be purchased separately as an accessory for the Hello
Bidet “Basic” version.
Thanks to the Addy adapter, you can connect Hello
Bidet to the faucet in a simple and fast manner,
without the need to mount the special lter holder .
Addy is ideal for use on the road, in a hotel or in case
of faucets with non-standard threads.
Addy can be connected to all faucets with circular
lter holder for water outlet with an outer diameter
from 16mm to 25mm and with a minimum height of
5mm (g.12).
WARNINGS AND RECOMMENDATIONS FOR THE USE
OF ADDY
• Gradually open the tap, not suddenly and not the
maximum water pressure;
• While the tap is open, do not try to reposion or
move Addy to avoid leaks;
• Inially, there may be some small leakage of water
from top of Addy for a few seconds, that are going
to disappear quickly. If the leakage were to be
prolonged or if it is excessive, you should repeat
the installaon procedure of Addy to the faucet;
• Make sure the lter holder is securely ghten to
the faucet to prevent leakage when the adapter
is mounted;
• The use of Addy in case of excessive pressure while
mounng, and repeated use on the same tap, may
cause light marks on the lter holder of the faucet
due to contact with the screws (for extended use
of Hello Bidet on the same faucet, we recommend
using the threaded special lters);
• It is not recommended to leave Addy mounted to
the faucet; if this happens, before each use check
that the hold is solid, making sure that the screw
(P1) is ghtened;
• When ghtening the screw (P1) be careful not to
deform the ring (Fig. 14);
• Should Addy come o the faucet, repeat the
procedure of assembly Addy to the faucet,
ghtening the screw P1 and the adjustment wheel
P2;
• Do not disassemble the components of Addy;
• Contains small parts - keep away from children.
ADDY - ASSEMBLY TO THE FAUCET
1. Place the lever in the open posion (Fig. 13) and
ghten the adjustment wheel (P2) unl the lever is
pulled, but without using excessive force;
2. Check that the ghtening screw is suciently
loosened to allow the inseron of Addy on the
To Next Page
Loading...