Weed Eater W25CB User Manual

ASSEMBLE SHAFT (MODELS WITH
KNOCKDOWN SHAFT)
a WARNING: To avoid personal injury or damage
to the unit, turn the unit off when assembling or
disassembling the shaft.
CAUTION: When assembling or disassembling the shaft,
place the unit on a at surface for stability.
1. Align the tab on the coupler (A) with the slot on the
lower tube (B).
2. Press the lower shaft into the coupler until the tube
ends are touching (C).
3. Install the coupler knob (D) on the same side as the
screw head and tighten securely.
CAUTION: To avoid personal injury or damage to the unit,
periodically check to ensure the tube ends are touching
and the knob is tight.
ADJUST HANDLE
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an upright position; retighten
wing nut.
ATTACH SHIELD
1. Mount shield to bracket by inserting TAB (A) on shaft bracket into
SLOT (B) in shield.
2. Rotate shield until bolt goes through bracket.
3. Attach wing nut (C).
C
A
B
FILL TANK
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of gasoline for a
50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
PLACE IN STARTING POSITION
Hold trimmer rmly on the ground (as shown).
START COLD ENGINE
Press the primer bulb 6 times rmly.
Move the choke lever to the full choke
(bottom) position.
Squeeze the throttle trigger while pulling
the starter rope handle 6 times rapidly.
Move the choke lever to the half choke
(middle) position.
Squeeze the throttle trigger while pulling
starter rope rapidly until the engine starts,
but no more than 6 pulls.
If the engine does not start, see
“STARTING A FLOODED ENGINE” in the
“OPERATION” section.
Move the choke lever to the run (top)
position.
Allow the engine to warm up for one minute.
START HOT ENGINE
Follow steps 4-6 in
START COLD ENGINE.
LT25NCOP
LT25NSOP
NOTE: Your product may differ slightly from the item shown.
Quick-Start Guide
a WARNING: Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
W25CB / W25CBK
W25SB / W25SBK
590203801 Rev. A 2017-02-24

Weed Eater W25CB Specifications

General

Brand	Weed Eater
Model	W25CB
Category	Trimmer
Language	English

Summary

Quick-Start Guide

Assembly Steps

Instructions for connecting the shaft, adjusting the handle, attaching the shield, and filling the fuel tank.

Starting Procedures

Basic steps for placing the unit and starting the engine from cold or hot.

Safety Information

Safety Symbols

Explanation of warning and safety icons used throughout the manual.

Operator Safety

Rules and precautions for personal protection during operation.

Unit and Fuel Safety

Guidelines for safe maintenance, unit handling, and fuel management.

Cutting, Transport, and Assembly

Cutting Safety

Precautions to prevent injury and damage during cutting operations.

Transporting and Storage

Guidelines for safely moving and storing the trimmer unit.

Assembly Instructions

Detailed steps for assembling the trimmer shaft, handle, and shield.

Operation Overview

Know Your Trimmer

Identification of the trimmer's parts and controls.

Before Starting Engine

Preparatory steps and checks required before igniting the engine.

Fueling and Stopping

Instructions for refueling the unit and shutting down the engine.

How to Start Your Unit

General overview of the process for starting the engine.

Operating Instructions and Tips

PPE and Tips

Recommendations for personal protective equipment and usage advice.

Trimmer Line Advance

How to extend the cutting line during operation.

Detailed Engine Starting

Step-by-step instructions for starting the engine from cold, hot, or flooded states.

Cutting Methods

Scalping

Technique for removing grass down to the ground level.

Mowing

Using the trimmer for mowing tasks in difficult-to-reach areas.

Trimming

Cutting grass and weeds around obstacles like trees and fences.

Sweeping

Using the trimmer's fanning action for cleaning debris.

Maintenance and Inspection

Routine Checks

Inspecting fasteners, parts, stop switch, fuel tank, and debris shield.

Unit Cleaning

Instructions for cleaning the trimmer unit and its labels after use.

Service and Adjustments

Air Filter Service

Procedures for cleaning or replacing the air filter for optimal performance.

Spark Plug Replacement

Instructions on how to replace the spark plug for easier starting.

Line Replacement

Steps for refilling the trimmer head spool with new cutting line.

Service Procedures

Trimmer Head Replacement

How to remove and install the trimmer cutting head.

Idle Speed Adjustment

Fine-tuning the engine's idle speed for proper operation.

Storage Guidelines

Daily Storage

Recommendations for short-term storage of the unit.

Seasonal Storage

Preparing the unit for long-term storage at the end of the season.

Troubleshooting and Fuel System

Fuel System Issues

Information regarding fuel tank and fuel line problems and solutions.

Troubleshooting Table

Solutions for common engine and unit malfunctions.

Emissions Control Warranty