Why is my Wessex AFE120 vibrating excessively?
Excessive vibration in your Wessex Lawn Mower can stem from several issues. Start by inspecting and replacing any damaged or missing blades. Then, check the flail rotor for any bending. A failed main rotor bearing could also be the culprit, so inspect the bearing and replace it if damaged. Lastly, ensure all nuts and bolts are tightened.
How to improve the cut quality of my Wessex AFE120 Lawn Mower?
If your Wessex Lawn Mower is producing a bad quality cut, there might be a few reasons. Check if your forward speed is too fast and reduce it. Another reason could be excessive blade wear, in which case you should replace the blades. Finally, slipping belts can also cause this issue, so make sure to tighten them.
What to do if my Wessex Lawn Mower is scalping the lawn?
Excessive scalping with your Wessex Lawn Mower is likely due to the cutting height being too low. To fix this, raise the cutting height.
How to prevent my Wessex AFE120 from leaving wheel track uncut?
Leaving a wheel track uncut with your Wessex Lawn Mower can be caused by a forward speed that's too fast. Try reducing your forward speed. Alternatively, the cutting height might be too high; in this case, lower the cutting height.
What to do if my Wessex Lawn Mower leaves a narrow strip uncut?
If your Wessex Lawn Mower is leaving a narrow strip uncut, it's possible that a blade is missing or broken. Inspect the blades and replace them as necessary.
Instructions to read the operating manual before using the machine.
Requirement for operators to wear ear protection when using the machine.
Safety instruction prohibiting adjustments or guard removal while the rotor is moving.
Warning to keep bystanders at a minimum distance of 20 meters from the operating machine.
Instruction to maintain a safe distance due to the risk of flying objects.
Guidance to lift the machine before turning it.
Recommendation to regularly inspect mower blades for condition and balance.
Warning to keep hands and feet away from moving parts of the machine.
Indication of lubrication points on the machine.
Details about the engine used in the Wessex AFE 120 Flail Mower.
Specifies the cutting width of the Wessex AFE 120 Flail Mower.
The total weight of the Wessex AFE 120 Flail Mower.
Description of the drive system used in the Wessex AFE 120 Flail Mower.
Recommended tyre pressure settings for the Wessex AFE 120 Flail Mower.
Safety rule: never adjust the machine while it is running or moving.
Safety rule: clear obstructions only when the machine is completely stopped.
Safety rule: only remove belt guards when the machine and engine are stopped.
Prohibition against removing any safety guards provided for user protection.
Safety rule: keep people, children, and animals at least 20 meters away.
Instruction to stand clear of the machine when the cutters are in motion.
Guidance to regularly inspect blades and their fixing bolts for wear and security.
Information regarding noise levels and required hearing protection for operators.
Details the noise level measured at the operator's ear for the flail mower.
Essential training requirements for ATV operators and those towing implements.
Recommendations for personal protective equipment when operating an ATV.
Advice to consult the ATV handbook before coupling implements.
Importance of understanding how ATV handling changes with coupled equipment.
Ensuring the implement's weight is within the ATV's capacity.
Precautions regarding weight transfer when towing loads on slopes.
Requirement to return the warranty registration card within seven days of purchase.
Procedure for reporting machine failures to the dealer for resolution.
Process for returning defective parts with a detailed failure statement.
List of conditions and damages not covered by the product warranty.
Statement that the warranty is valid only for the original purchaser.
Policy stating that Wessex International's warranty decisions are final.
Recommendation for initial inspection of fasteners after one hour of operation.
Instruction for positioning the towing vehicle and connecting the ball hitch.
Guidance on securing the engine cut-off switch for operator accessibility.
Ensure the rotor is stopped before adjusting the cutting height.
Instruction to adjust the rear roller based on cutting conditions and material volume.
Guidance on correct positioning of the adjustment handle for full height adjustment.
Operating instructions for the centrifugal clutch system and engine throttle settings.
Guidance on selecting appropriate forward speed based on cutting material and conditions.
Explanation of how to adjust the cutting height using the adjustment handle.
Step one in belt adjustment: remove the belt cover.
Step two: loosen the clamping bolt on the jockey pulley bracket.
Step three: adjust belt tension using the adjusting screw and secure.
Step four: retighten the previously loosened clamp bolt.
Step five: replace the belt cover after adjustment.
Critical check of all fasteners for tightness after the first hour of use.
Daily lubrication requirement for the two main rotor bearings.
Daily lubrication requirement for the two roller bearings.
Daily lubrication requirement for the two wheel bearings.
Daily inspection of flail blades is crucial to prevent rotor imbalance and damage.
Action to take if mower vibrates: stop and investigate for blade or object issues.
Procedure for accessing and changing flail blades, requiring unhitching and lifting.
Ensure rotor balance by fitting new bolts/nuts and full sets of flails.
Information on obtaining spare parts through the Wessex dealer network.
Contact details for nearest spare parts suppliers and technical assistance.
Troubleshooting issue: mower not cutting a continuous track.
Troubleshooting issue: poor or uneven quality of the cut material.
Troubleshooting issue: a narrow strip of uncut material remains.
Troubleshooting issue: machine experiencing excessive and potentially damaging vibration.
Troubleshooting issue: mower cutting too low and damaging the turf.
Inspect and repair any worn or broken parts before storage.
Carefully inspect flail blades, rotor, and bearings for condition.
Remove belts and ensure the rotor spins freely for storage.
Verify the condition of belts before re-fitting them after storage.
Thoroughly clean the machine to remove oil, grease, and debris.
Apply grease to all lubrication points to prevent corrosion during storage.
Check or change engine oil based on usage hours before storage.
General| Brand | Wessex |
|---|---|
| Model | AFE120 |
| Category | Lawn Mower |
| Language | English |
To Next Page
