Westermann WR 870 Battery

Other manuals for Westermann WR 870 Battery

Questions and Answers

J
Justin CarrilloAug 8, 2025
What to do if the brush on my Westermann WR 870 Battery Floor Machine doesn't turn even after moving the direction change lever?
- A
  amy14Aug 9, 2025
  If the brush on your Westermann Floor Machine does not turn despite moving the director change lever, consider the following: * Ensure the direction of rotation change lever is in the correct drive position. * Check the V-belt and replace it if defective. * Tighten the drive belt tensioning bolt. * Adjust the toothed belt tensioning device if the timing belt pretension is insufficient (lever can be pushed beyond the intended holes).
J
Joe LivingstonAug 13, 2025
What to do if the brush on my Westermann WR 870 Battery does not turn or stops at low resistance?
- C
  Charles LopezAug 13, 2025
  If the brush on your Westermann Floor Machine doesn't turn or stops when it meets low resistance, it could be due to: 1. A defective V-belt: Inspect the V-belt and replace it if necessary. 2. A defective toothed belt: Examine the toothed belt and replace if needed. 3. Insufficient drive belt pretension: Tighten the drive belt.
K
Kayla WardAug 17, 2025
How to fix a Westermann Floor Machine brush that does not turn correctly?
- H
  Henry KennedyAug 17, 2025
  If the brush on your Westermann Floor Machine isn't turning correctly, check these potential causes: * Ensure the direction selector lever is in the neutral position. If not, move it to neutral. * Adjust the sweeping height to suit the conditions. * Check all screws and tighten any that are loose.
J
Jennifer PowellAug 21, 2025
What to do if the brush does not turn on my Westermann WR 870 Battery Floor Machine?
- D
  djohnsonAug 21, 2025
  If the brush on your Westermann Floor Machine isn't turning, even when you've moved the direction lever, there could be several reasons. First, make sure the direction selector lever is in a drive position and not in neutral. Next, check that the sweeping height is appropriate for the surface. Also, inspect all screws and tighten any that are loose. Examine the V-belt and toothed belt for any defects, replacing them if needed. Ensure the drive belt and toothed belt have sufficient tension by tightening the drive belt tensioning bolt and adjusting the toothed belt tensioning device. Finally, if the engine is malfunctioning, refer to the engine manual's troubleshooting section.
N
Nichole RodriguezAug 26, 2025
Why does the brush not turn on my Westermann Floor Machine even when moving the direction lever?
- J
  Jacob DavisAug 26, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it could be due to the direction selector lever not being in the neutral position. Move the direction selector lever to the neutral position. It is also possible that the sweeping height is wrong. Adjust the sweeping height to the conditions.
A
ashley26Aug 30, 2025
How to troubleshoot a Westermann Floor Machine when the brush won't turn?
- G
  gboydAug 30, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it may be caused by loose screw connections. Check all screws and tighten them if necessary. Also, the V-belt or toothed belt could be defective, so check them and replace if needed.
A
Amanda VillaSep 3, 2025
What to do if the drive belt pretension is insufficient on my Westermann Floor Machine?
- C
  Crystal ChanSep 3, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it might be because the drive belt pretension is insufficient. To resolve this, simply tighten the drive belt tensioning bolt.