Westermann WR 870 Honda PRO

Other manuals for Westermann WR 870 Honda PRO

User Manual65 pages

Questions and Answers

J
Joseph MccarthyAug 5, 2025
What to do if the brush on my Westermann WR 870 Honda PRO doesn't turn even after moving the direction change lever?
- J
  Jacqueline HebertAug 5, 2025
  If the brush on your Westermann Floor Machine does not turn despite moving the director change lever, consider the following: * Ensure the direction of rotation change lever is in the correct drive position. * Check the V-belt and replace it if defective. * Tighten the drive belt tensioning bolt. * Adjust the toothed belt tensioning device if the timing belt pretension is insufficient (lever can be pushed beyond the intended holes).
B
Brandon DillonAug 9, 2025
What to do if the brush on my Westermann WR 870 Honda PRO Floor Machine does not turn or stops at low resistance?
- J
  James BrooksAug 9, 2025
  If the brush on your Westermann Floor Machine doesn't turn or stops when it meets low resistance, it could be due to: 1. A defective V-belt: Inspect the V-belt and replace it if necessary. 2. A defective toothed belt: Examine the toothed belt and replace if needed. 3. Insufficient drive belt pretension: Tighten the drive belt.
C
charles20Aug 14, 2025
How to fix a Westermann WR 870 Honda PRO brush that does not turn correctly?
- T
  Teresa MillerAug 14, 2025
  If the brush on your Westermann Floor Machine isn't turning correctly, check these potential causes: * Ensure the direction selector lever is in the neutral position. If not, move it to neutral. * Adjust the sweeping height to suit the conditions. * Check all screws and tighten any that are loose.
C
Cole GambleAug 18, 2025
What to do if the brush does not turn on my Westermann Floor Machine?
- M
  Mr. Bradley Scott DDSAug 18, 2025
  If the brush on your Westermann Floor Machine isn't turning, even when you've moved the direction lever, there could be several reasons. First, make sure the direction selector lever is in a drive position and not in neutral. Next, check that the sweeping height is appropriate for the surface. Also, inspect all screws and tighten any that are loose. Examine the V-belt and toothed belt for any defects, replacing them if needed. Ensure the drive belt and toothed belt have sufficient tension by tightening the drive belt tensioning bolt and adjusting the toothed belt tensioning device. Finally, if the engine is malfunctioning, refer to the engine manual's troubleshooting section.
J
Jessica TapiaAug 22, 2025
Why does the brush not turn on my Westermann WR 870 Honda PRO Floor Machine even when moving the direction lever?
- D
  Dana RobinsonAug 22, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it could be due to the direction selector lever not being in the neutral position. Move the direction selector lever to the neutral position. It is also possible that the sweeping height is wrong. Adjust the sweeping height to the conditions.
J
John MasonAug 27, 2025
How to troubleshoot a Westermann Floor Machine when the brush won't turn?
- D
  Dr. David Brown DVMAug 27, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it may be caused by loose screw connections. Check all screws and tighten them if necessary. Also, the V-belt or toothed belt could be defective, so check them and replace if needed.
R
Ryan RomeroAug 31, 2025
What to do if the drive belt pretension is insufficient on my Westermann WR 870 Honda PRO?
- A
  anthony48Aug 31, 2025
  If the brush on your Westermann Floor Machine isn't turning when you move the direction lever, it might be because the drive belt pretension is insufficient. To resolve this, simply tighten the drive belt tensioning bolt.

Summary

Safety

Intended Use of the Machine

Specifies the proper applications for the Westermann Radial Sweeper WR 870.

Operator Requirements

Outlines necessary qualifications and conditions for operating the machine safely.

Danger Area

Defines the hazardous zone around the machine during operation and necessary precautions.

Foreseeable Misuse

Emergency Procedures

Details actions to take in case of personal injury, fire, or technical complications.

Operator Responsibility

Defines the operator's obligations, especially for commercial use and occupational safety.

Operator Obligations

Lists specific duties of the operator for machine maintenance, safety equipment, and documentation.

Personal Responsibility and Qualifications

Covers basic requirements for operators and qualifications for specialists and instructed personnel.

Observance of Operating Manual

Residual Hazards and Protective Measures

Addresses the inherent residual risks and necessary protective measures despite safety instructions.

Personal Protective Equipment (PPE)

Details required PPE for safe operation, including foot, clothing, hand, and hearing protection.

Safety Instructions for Operator;User

Technical Specifications

Detailed Technical Data

Assembly and First Start-up

Safety Considerations

Highlights safety aspects during installation and handling of the machine.

First Start-up Procedure

Start-up Procedures

Adjusting Handle Height

Brush Adjustment

Explains how to adjust brush height based on debris type and wear.

Starting the Honda Engine

Details the steps for starting the WR 870 Honda engine, including neutral position checks.

Opening the Fuel Valve

Cold Start Procedure

Describes the process for starting the engine in cold conditions using the choke.

Starting at Operating Temperature

Using the Starter Cord

Determining Sweeping Direction

Explains how to set the direction of brush rotation using the hand lever.

Stopping the Honda Engine

Provides instructions on how to safely stop the WR 870 Honda engine.

Charging the WR 870 Battery

Details the process of connecting the battery to the charger for automatic charging.

Starting the Battery Model

Guides on starting the WR 870 Battery model on a level surface with the fuse in place.

Operation

Service Interval and Maintenance

Maintenance and Servicing

General Maintenance Guidelines

Honda Engine Maintenance

Brush Element Replacement

Brush Removal and Installation

V-Belt Replacement and Tightening

Details how to loosen, remove, and re-tension V-belts for optimal power transmission.

Replacing Direction Change Belt

Clockwise V-Belt;Toothed Belt

Clockwise Rotating V-Belt

Screw Connections and Torque

Fuse Replacement

Residual Risks

Electrical Hazards

Details risks associated with electrical voltage and necessary precautions for safe operation.

Hot Surfaces

Warns about the risk of burns from hot machine parts and required safety measures.

Risks of Improper Operation

Explains dangers from incorrect machine operation and necessary preventative steps.

Risks from Moving Components

Highlights hazards from moving machine parts and safety measures to prevent accidents.

Machine Recoil Risks

Addresses risks from unpredictable machine movements and necessary actions to mitigate them.

Storage Conditions

Troubleshooting

Troubleshooting WR 870 Honda;PRO

Lists common faults for the Honda/PRO model, their causes, and remedies.

Troubleshooting WR 870 Akku;PRO

Lists common faults for the Akku/PRO model, their causes, and remedies.

Decommissioning and Disposal

Dismantling and Disposal