Westinghouse WHG642SA Product Details

Westinghouse WHG642SA

6 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

WHG642SA

RRP AUS $599.00

60cm stainless steel gas cooktop with FamilySafe (TM) trivets and

high-powered wok burner.

WHG642SA - 60cm stainless steel gas cooktop

Table of Contents

Other manuals for Westinghouse WHG642SA

User Manual20 pages

Questions and Answers:

D
Daniel BlankenshipJul 31, 2025
Why won't my Westinghouse WHG642SA burner light but the sparker is working?
- S
  scottcrystalAug 1, 2025
  If the Westinghouse cooktop burner won't light even though the sparker is working, several issues could be the cause. First, make sure you're holding the knob down long enough in the ‘High’ position, around 5 seconds, so the flame safeguard can engage. Check that the gas supply valve is turned on. Ensure you're turning the correct knob for the burner you want to light. Also, inspect the ignition area for any blockages and make sure the ignition spark plugs are clean and dry.
M
Michael RiveraAug 5, 2025
What to do if the flames are not staying on when knob released on Westinghouse Cooktop?
- P
  Phillip AllenAug 5, 2025
  If the flames on your Westinghouse cooktop aren't staying on after you release the knob, it could be due to a few reasons. Ensure you're holding the knob down long enough in the ‘High’ position for the flame safeguard to engage. The knob must be set between ‘High’ and ‘Low’. Also, check for any dirt or spillage on the flame safeguard sensor and clean it if necessary.
M
Morgan OlsenAug 10, 2025
Why is my Westinghouse WHG642SA Cooktop stainless steel discolored?
- B
  blakeolsonAug 10, 2025
  If your Westinghouse cooktop stainless steel is discolored, it could be because you're using a pot or pan that's too large. Make sure the pot sizes you're using are as per the user manual requirements.
J
Jillian HayesAug 15, 2025
Why is there no spark when I turn the control knob on my Westinghouse Cooktop?
- C
  Catherine RodriguezAug 15, 2025
  If you're not getting a spark when you turn the control knob on your Westinghouse cooktop, the electricity supply might be disconnected or switched off, so switch it on or check the fuses. The ignition spark plugs might also be wet or dirty, so dry or clean them.
J
Jean RussellAug 20, 2025
How to fix uneven flames on a Westinghouse WHG642SA Cooktop?
- P
  Patrick DanielAug 21, 2025
  Uneven or lifting flames on your Westinghouse cooktop can be caused by blocked or wet flame ports, so clean or dry them. Also, the burner might be incorrectly fitted, so ensure it's fitted correctly.
D
David ChambersAug 26, 2025
Why are the benchtop or knobs overheating on my Westinghouse WHG642SA?
- S
  ssnyderAug 26, 2025
  Overheating of the benchtop or knobs on your Westinghouse cooktop can be due to using the wrong cooking pot or pan. Check Figure 3 for the correct pot or pan to use. It could also be that the pot or pan isn't located on the burner properly, so ensure it's centrally located.

Westinghouse WHG642SA Specifications

General

Type	Gas Cooktop
Number of Burners	4
Material	Stainless Steel
Ignition Type	Electronic
Fuel Type	Natural Gas or LPG
Ignition System	Electronic

Related product manuals

Preview: Westinghouse WHG952SB

Westinghouse WHG952SB

Westinghouse WHG956SA

Preview: Westinghouse WHIC02K

Westinghouse WHIC02K

Preview: Westinghouse WHI955BB

Westinghouse WHI955BB

Preview: Westinghouse WHC643BC

Westinghouse WHC643BC

Preview: Westinghouse WHI323BD

Westinghouse WHI323BD

Westinghouse GHL95