Need help?Do you have a question about the Westwood W Series and is the answer not in the manual?
General| Brand | Westwood |
|---|---|
| Model | W Series |
| Category | Lawn Mower |
| Language | English |
Read instructions, understand controls, and ensure safe operation. Never allow unauthorized users.
Check machine compliance, wear protective gear, inspect area, handle fuel safely, check components.
Read instructions, familiarise with controls, operate safely, avoid slopes, watch for traffic, never operate with guards off.
Adjust the operator's seat forward or backward for comfort. Ensure it is latched.
Controls engine start/stop. Use key and start button. Remove key to prevent unauthorised use.
Used for cold starts with fast throttle. Cancel as soon as possible. Do not use for warm engines.
Lever controls forward (FAST) and backward (SLOW). Operate on FAST setting for mowing.
Monitors engine speed. Ensure it does not fall below 2600rpm during cutting for optimal performance.
Tracks engine running time for service intervals. Machine requires service after 50 hours or yearly.
Foot pedals control forward (A) and reverse (B) speed. Depress pedal for acceleration.
Release parking brake, depress pedal A to move forward, pedal B to reverse. Speed increases with pedal depression.
Release drive pedal for natural braking. Release gradually for smooth stop, rapidly for emergency stop.
Release pedals, pull parking brake lever upright. 'P' indicated on dashboard. Adds to engine braking effect.
Disengages hydrostatic transmission for freewheeling. Pull lever to disengage, push back to re-engage.
Engages/disengages blade clutch. Headlights flash when cutter is running. Safety interlocks prevent operation without operator.
Raises/lowers cutter deck for transport. Safety interlock prevents cutter running when raised.
Momentary switch turns headlights on/off. Requires ignition. Headlights illuminate permanently when cutter is running.
Rotary switch adjusts cutting height (0-9). Adjust continuously for best results. Avoid downward adjustments while moving.
Manual lever adjusts cutting height. Do not set to very low settings to avoid scalping.
Save time, feed lawn. Reduce grass height by max 1/3 per pass. Mow often. Keep deck clean. Check blades are sharp.
Alternative for long grass. Use higher settings (7-9) for very tall grass. Maintain engine speed.
Combination deck for mulching and rear discharge. Can be switched to rear discharge by removing parts.
Refer to engine manufacturer's handbook for details. Ensure proper engine care for longevity.
Low maintenance sealed unit. Use special 2-stage charger. Standard chargers may cause premature failure.
Clean deck regularly. Use wash position or remove deck. Avoid pressure washers. Clean after use for best results.
Deck drive belt is self-tensioned. Check belt is correct if tension is problematic.
Self-tensioning belt. Adjustment by dealer is recommended. Improper adjustment can cause damage.
Located under foot plate. Check oil level when cold. Expand when warm. Top up via rubber grommet if needed.
Instructions for changing belts for different deck sizes. Requires deck removal for belt replacement.
Procedure to remove seat box for access. Involves unbolting and disconnecting wires. Reassembly notes included.
Steps to remove cutter deck for cleaning or transport. Involves disconnecting belts, pins, and linkages.
Steps to reattach cutter deck. Align parts, reconnect belt, pins, and linkages. Check tension and connections.
Controlled by cable and chain. Annual check by dealer recommended. Tension adjustment procedure provided.
Adjustments for even cut. Front should be 8-10mm higher than back. Side-to-side tolerance is 3mm.
Common issue due to thorns. Use tyre sealant. Check rims for damage. Remove sharp objects from cutting area.
Check tyre inflation to correct pressures. Ensure you are not driving too fast for conditions.
Procedure to remove front wheels for repair or maintenance. Includes jacking points and torque settings.
Procedure to remove rear wheels. Involves removing hub cap, nut, and wheel. Torque settings provided.
Check operator presence, safety switches, battery charge, transport lever position, and fuses.
Check tyre pressure, deck levelling, blade condition, and grass build-up in the deck.
Check tyre inflation, rear axle pivot, deck suspension movement, and side deck level.
Check front-to-back deck levelling, blade condition, and grass in liner.
Check belt tension, deck clogging, and belt wear. Do not attempt blade changes yourself.
Check parking brake, seat presence, dump valve, battery connections, and fuses.
Check fuel level, spark plug connection/condition, fuel filter, and fuses.
Check fuel level, air filter, cooling intakes, and fuses.
Check cutter fuse, operator presence on seat, battery charge, and transport lever position.
Check 30 amp fuse, battery charge, and ignition fuse (Fuse 2).
Check 4amp contact breaker reset. Ensure nothing is jammed between deck and chassis.
Indicates battery is not charging. Check main charge fuse.
Warns of exceeding 25° slope angle with flashing display and siren. Do not operate on slopes steeper than 25°.
Additional neutral valve for rear transmission freewheeling. Safety switch linked to park brake.
Located under right control pod. Check level when cold. Oil expands when warm. Contact dealer if level drops.
Covers weight, fuel capacity, transmission, turning radius, forward speeds, and tyre pressures for 2WD models.
Details engine specs by model and overall lengths for different deck sizes.
Covers weight, fuel capacity, transmission, turning radius, forward speeds, and tyre pressures for 4WD models.
Details engine specs by model and overall lengths for different deck sizes for 4WD models.
Record of service history for the Westwood W Series. Includes spaces for dealer stamp and service details.
Declaration of product conformity with applicable standards and directives. Signed by manufacturer representative.
To Next Page
