To Next PageTo Next PageWhy won't my Whirlpool WFW9050XW Washer run or fill?
If your Whirlpool Washer won’t run or fill, or stops working, ensure both hoses are attached and have water flowing to the inlet valve. Also, check that both hot and cold water faucets are turned on. Make sure that the inlet valve screens are not clogged, and inspect the inlet hoses for any kinks that may be restricting water flow.
Why is my Whirlpool WFW9050XW not draining/spinning and loads are still wet?
If your Whirlpool washer is not draining or spinning and loads are still wet, consider the following: * Ensure small items haven't been caught in the pump by emptying pockets and using garment bags. * Check the drain hose installation, ensuring it doesn't extend into the standpipe more than 4.5" (114 mm). * Lower the drain hose if the end is higher than 96" (2.4 m) above the floor and remove any clogs from the drain hose. * Make sure the drain hose fits loosely but securely in the standpipe, without being sealed with tape to allow for an air gap. * Use cycles with higher spin speeds and avoid tightly packing or unbalancing the load.
What to do if 'Sd' (Excess suds) appears in my Whirlpool Washer display?
If 'Sd' (Excess suds) appears on your Whirlpool Washer display, allow the machine to continue its suds reduction routine. Ensure you are only using HE detergent, measuring the correct amount based on load size and following the detergent manufacturer’s instructions. Also, make sure the hot and cold inlet hoses are not reversed, both hoses are attached with water flowing to the inlet valve, and both hot and cold water faucets are on. Check the inlet valve screens for clogs and remove any kinks in the inlet hose.
How to stop my Whirlpool Washer from vibrating, rocking, or “walking”?
If your Whirlpool washer is vibrating, rocking, or “walking”, make sure the front and rear feet are in firm contact with the floor and the washer is level. The jam nuts must be tight against the bottom of the cabinet. If the flooring is uneven, placing a 3/4" (19 mm) piece of plywood under the washer can help reduce sound. Avoid tightly packing the load or washing single items; balance single items with a few extra items. Use medium or low-speed spin for oversized, non-absorbent items and the Delicate cycle for items like poly-filled jackets.
Why is water or suds leaking from the door or rear of my Whirlpool WFW9050XW?
If you notice water or suds leaking from the door or rear of your Whirlpool washer, it may be due to using non-HE detergent or using too much HE detergent. Only use HE detergent, measuring it carefully and following the manufacturer's directions based on your load requirements. Water can also drip off the inside of the door when opened after a cycle has started. Periodically clean the underside of the glass window to prevent potential leaks.
What to do if the door of my Whirlpool Washer will not unlock?
If the door of your Whirlpool washer will not unlock, and the “Add a Garment” light is lit, press START/PAUSE once. The door should then unlock.
What to do if F9E1 (drain pump system error) appears in Whirlpool WFW9050XW display?
If F9E1 (drain pump system error) appears on the display of your Whirlpool washer, check the plumbing to ensure the drain hose is correctly installed and doesn't extend into the standpipe farther than 4.5" (114 mm). Make sure the drain hose is not kinked, pinched, or blocked, and remove any clogs. Use the drain hose form and securely attach it to the drainpipe or tub. If the end of the drain hose is higher than 96" (2.4 m) above the floor, lower it.
Why are my whites gray and colors dingy after washing in my Whirlpool WFW9050XW?
If you're experiencing gray whites or dingy colors after washing in your Whirlpool washer, it may be due to improper sorting of loads. Dye transfer can occur when mixing whites and colors, so sort dark clothes from whites and lights. Also, ensure wash temperatures are adequate; use hot or warm washes if safe for the load and confirm your hot water system provides sufficient hot water. Use more detergent for washing heavy soils in cold or hard water. Avoid overfilling the dispenser, and clean the dispenser compartments regularly.
Why is my Whirlpool WFW9050XW Washer not cleaning or removing stains?
If your Whirlpool washer is not cleaning or removing stains effectively, ensure the washer is loaded loosely to allow items to move freely. Consider that hard water or high iron levels in the water may affect cleaning performance. You may want to avoid using a fabric softener dispensing ball and consider switching to liquid detergent. For tough cleaning, use the Heavy Duty cycle.
How to clear an error code on my Whirlpool WFW9050XW Washer?
If an error code appears on the display of your Whirlpool Washer, correct any possible issues, then press START/PAUSE once to clear the code. Press START/PAUSE again to restart the washer. If the code reappears, call for service.
General| Brand | Whirlpool |
|---|---|
| Model | WFW9050XW |
| Type | Front Load Washer |
| Color | White |
| Energy Star Certified | Yes |
| Wash Cycles | 12 |
| Steam Function | Yes |
| Sanitize Cycle | Yes |
| Voltage | 120 V |
| Frequency | 60 Hz |
| Width | 27 inches |
Key safety precautions for operating the washing machine.
Guidance on selecting and using High Efficiency detergents.
How to start, pause, continue, or cancel wash cycles.
Procedure for keeping the washer interior clean and odor-free.
Steps to clear and restart when error codes are shown.
Troubleshooting steps for excessive suds indicated by 'Sd'.
Troubleshooting steps for water supply errors indicated by 'F8E1'.
Troubleshooting steps for drain pump system errors.
Troubleshooting general system error codes.
Causes and solutions for water leaking from the door or cabinet.
Addressing leaks from door or rear cabinet due to suds or door opening.
Troubleshooting power, water supply, and door latch issues.
Further checks for door closure, detergent, and cycle interruption.
Solutions for loads remaining wet due to drain/spin issues.
Solutions for cleaning performance issues and stain removal.
