How to fix a Whirlpool AWE 6112 that won't start?
If your Whirlpool Washer doesn't start and no indicator lights are on, check these items: * Ensure the plug is correctly inserted into the socket. * Test the socket or fuse with a table lamp or similar appliance to see if it functions. * If the washing machine has automatically switched off to save energy, turn the programme selector to “Off/O” and then to the desired programme again.
What to do if Whirlpool Washer won't start after pressing 'Start'?
If your Whirlpool Washer doesn't start even after pressing “Start(Pause)”, check these items: * Ensure the lid is properly closed. * If available, check if the “Child lock” function is activated. To unlock the buttons, push the temperature and spin speed button simultaneously and hold them for at least 3 seconds, until the key symbol on the display disappears.
How to stop Whirlpool AWE 6112 from vibrating?
To reduce vibration in your Whirlpool Washer during the spin cycle: * Ensure the washing machine is level and the feet are properly adjusted. * Make sure the transport bracket has been removed before using the washing machine.
Why are the spin results poor on my Whirlpool AWE 6112 Washer?
If the final spin results are poor on your Whirlpool Washer, here are some potential reasons: * Unbalance during spinning may have prevented the spin phase to protect the washing machine. * Excessive foam formation might have prevented spinning; select and start the “Rinse & Spin” programme, and avoid using too much detergent. * The “Spin” button might be set to a low spin speed.
Why does my Whirlpool Washer show an unbalance error?
If your Whirlpool Washer displays an unbalance error and the laundry is still very wet, it means the laundry load was unbalanced during spinning, preventing the spin phase to avoid damage to the machine. To resolve this: * Avoid washing small laundry loads. * When washing a large or heavy item, add other laundry items of different sizes. If you want to spin the wet laundry, add more items and then select and start the “Rinse & Spin” programme.
Why is there detergent left in my Whirlpool AWE 6112 dispenser?
If your Whirlpool Washer's detergent dispenser contains residues after a wash, it could be due to: * The detergent dispenser not being properly installed or being blocked. * The filter in the water inlet hose being blocked.
What does 'Clean pump' mean on Whirlpool Washer?
If your Whirlpool Washer displays a “Clean pump” message, check these items: * Ensure there are no kinks in the drain hose. * Check if the filter or pump is blocked. * Ensure the drain hose is not frozen. After resolving the issue, select and start the “Drain” programme or push the “Reset” button for at least 3 seconds, then restart the desired programme. If the fault persists, contact After-Sales-Service.
What to do if my Whirlpool AWE 6112 stops mid-cycle?
If your Whirlpool Washer stops during a cycle and the Start/Pause light is blinking, consider the following: * If the “Rinse hold” option is activated, terminate it by pressing “Start(Pause)” or by choosing and starting “Drain”. * If the programme has been changed, reselect the desired programme and press “Start(Pause)”. * If the programme was interrupted and the lid opened, close the lid and restart the programme. * Check that the water tap is open and the water inlet hose isn't kinked, as this can activate the appliance’s safety system and cause the “Water tap closed” indicator to light up.
Why does Whirlpool AWE 6112 Washer cycle time change?
The programme duration of your Whirlpool Washer can vary due to factors like excessive foam, load unbalance, or low inlet water temperature. The washer adapts to these conditions, recalculating the duration as needed. For small loads, the programme time may be reduced by up to 50%.
What does 'Water tap closed' mean on Whirlpool AWE 6112?
If your Whirlpool Washer displays a “Water tap closed” message, verify the following: * The water tap is fully open and the water supply pressure is sufficient. * There are no kinks in the water inlet hose. * The mesh filter of the water supply hose is not blocked. * The water hose is not frozen. * If your appliance has a water supply hose with a safety valve inspection window, check if it is red and replace the hose if needed. After resolving the issue, restart the programme by pressing “Start (Pause)”. If the fault occurs again, contact After-Sales Service.
General safety precautions for indoor use, handling flammable materials, child safety, and electrical safety.
Guidelines for correct disposal of the appliance according to WEEE directives and local environmental regulations.
Guidance on removing the transport bracket and screws before operating the machine.
Steps for installing the machine on a stable surface, adjusting feet, and ensuring ventilation.
Requirements for connecting the water supply, including tap type, pressure, and hose usage.
Instructions for connecting the drain hose to an appropriate outlet and preventing siphoning.
Safety guidelines for electrical connection, emphasizing qualified technicians and proper wiring.
Detailed steps to remove the transport bracket and secure the machine before use.
Procedure for adjusting the machine's feet to ensure it is level and stable on the floor.
Emphasizes the critical importance of earthing the washing machine for electrical safety.
To Next Page
General