To Next PageTo Next PageHow to fix a Whirlpool AWOC 0714 Washer that won't start and has no lights?
If your Whirlpool washer is not starting and no indicator lights are on, check that the plug is properly inserted into the socket. Verify that the socket or fuse is functioning correctly by testing it with a table lamp or similar appliance. Also, ensure that the “On/Off” button has been pressed, if your model has one.
What to do if Whirlpool AWOC 0714 won't start after pressing start?
If your Whirlpool Washer does not start even after pressing “Start(Pause)”, make sure the door is properly closed. Also, check if the “Child lock/Lock buttons” feature is activated. To unlock, press and hold the two buttons marked with the key symbol simultaneously for at least 3 seconds, until the key symbol disappears from the display.
Why does my Whirlpool AWOC 0714 vibrate so much during spin cycle?
If your Whirlpool Washer vibrates excessively during the spin cycle, it may be because the transport bolts have not been removed. It is essential to remove these before using the machine. Also, ensure that the appliance is level; refer to the separate “Installation Guide” for instructions.
Why are there detergent residues on laundry after washing in my Whirlpool AWOC 0714?
If you see detergent residues on your laundry after washing with your Whirlpool Washer, it could be due to insoluble compounds in phosphate-free powder detergents, especially on dark fabrics. To resolve this, avoid overdosing detergent, use liquid detergent, select the “Intensive Rinse” option if available, and brush out the fabric after washing.
Why are the spin results poor on my Whirlpool AWOC 0714 Washer?
If your Whirlpool Washer's final spin results are poor, it could be because heavy items prevented proper spinning. Try adding smaller articles of laundry and repeating the spin cycle. Excessive foam formation could also prevent spinning; select and start the “Rinse & Spin” program, and avoid using too much detergent.
What to do if the Whirlpool Washer says “Water tap closed”?
If your Whirlpool Washer displays the “Water tap closed” message, it indicates that the appliance is not getting enough water. Check that the water tap is fully open and the water supply pressure is sufficient. Also, inspect the water inlet hose for any kinks or blockages and ensure the mesh filter of the water inlet hose is not blocked. Finally, verify that the water hose is not frozen. If your water inlet hose has a safety valve inspection window and it's red, replace the hose.
Why does my Whirlpool AWOC 0714 stop mid-cycle and the start light blinks?
If your Whirlpool washer stops during the program and the “Start(Pause)” light is blinking, several issues could be the cause. The “Rinse hold” function might be activated; press the “Start(Pause)” button to start the drain program. You may have inadvertently changed the program; reselect the desired program and press “Start/Pause”. The program might have been interrupted; close the door and restart the program by pressing “Start(Pause)”. The appliance’s safety system could be activated. In this case, refer to the “Description of failure .. indications” in your program chart. Finally, the water tap may not be opened, or the water inlet hose may be kinked or blocked, indicated by the “Water tap closed” light.
What does “Clean pump” mean on my Whirlpool Washer?
If your Whirlpool Washer displays the “Clean pump” message, it means waste water is not being pumped out. Check the drain hose for kinks or blockages. Also, inspect the filter or pump for blockages, making sure the water has cooled before draining. Finally, ensure the drain hose is not frozen.
What does “Service” mean on my Whirlpool AWOC 0714?
If your Whirlpool washer displays the “Service” message, it could indicate several issues. It could be an electrical module fault; try pushing the “Reset” button for at least 3 seconds. It may also appear if you've washed very water-soaking laundry or overloaded the machine for a small-load program. A Waterstop fault could also trigger this message; turn the program selector to the “Off/O” position, disconnect the mains plug, and turn off the water tap. Finally, too much foam could have interrupted the wash program; if your washing machine has a “Dosing Aid” function, check if the dosing values set for the different program groups correspond to the dosing values recommended for the detergents you use.
Why is the Whirlpool Washer programme duration longer than indicated?
The duration of a wash cycle on your Whirlpool washing machine can vary depending on factors such as excessive foam formation, load imbalance due to heavy laundry items, and prolonged heating time resulting from low inlet water temperature.
General| Capacity | 7 kg |
|---|---|
| Maximum spin speed | 1400 rpm |
| Spin Speed | 1400 RPM |
| Color | White |
| Loading type | Front Loading |
| Energy Rating | A |
| Water Consumption | 45 L |
Remove transport bolts to prevent internal damage and cover openings with caps.
Install on a solid, level floor, adjust feet, use plywood for wooden floors.
Electrical connections by qualified technician, use earthed socket.
Crucial safety guidelines for indoor use, child safety, and operation.
Tips to optimize water, energy, and detergent use for efficiency.
Access for filter cleaning and emergency draining.
Used to level the appliance on the floor.
Sort laundry by fabric type, colour, and size for efficient washing.
Load items loosely into the drum without overfilling for optimal washing.
Follow detergent dosage recommendations based on load size, soiling, and water hardness.
Chamber for main wash detergent, stain remover, or water softener.
Chamber for fabric softener or liquid starch.
Add chlorine bleach to the softener chamber, run rinse/spin afterwards.
Remove, wash, and reassemble the detergent dispenser drawer and siphon.
Check hoses for brittleness/cracks, replace if needed.
Clean the mesh filter in the water inlet hose by closing the tap and unscrewing.
Check plug, socket, fuse, and the On/Off button.
Ensure transport bolts are removed and the appliance is level.
Check for unbalanced loads, excessive foam, or low spin speed.
No or insufficient water supply. Check tap, hose, and filter.
Waste water not pumped out. Check drain hose, filter, or pump.
Drawer for raising the machine for easier loading and storage.
Kit to fix a dryer on top of the washing machine.
Kit for building the machine under a kitchen worktop.
Procedure for replacing the fuse in a BS 1363A plug.
Guidance on plug suitability and professional replacement if needed.
Instructions for removing transport bolts, emphasizing their importance.
Adjust the machine's feet to ensure it is level on the floor.
Connect the drain hose to a siphon or outlet, ensuring no kinks.
Connect the water inlet hose to the machine and the tap, checking for leaks.
