To Next PageTo Next PageWhy does the burner flame float and lift off ports on my Whirlpool Residential Gas Water Heater?
A burner flame that floats and lifts off ports can be caused by: * An orifice that is too large; replace it with the correct orifice. * High gas pressure; check with your gas utility company. * A clogged flue; clean the flue and burner, and locate the source of the blockage. * Cold drafts; locate the source and correct it.
How to fix Whirlpool Water Heater burner that will not ignite?
If the burner of your Whirlpool Water Heater won't ignite, try the following: * Turn the temperature dial to your desired setting. * Check with your gas utility company. * Notify the utility company to install a trap in the gas line. * Clean and locate the source of any issues, then correct them. * Replace the gas control valve or thermostat. * Provide fresh air ventilation. * Cycle the power to the water heater off and on. If the problem continues, replace the flue damper.
How to fix Whirlpool Water Heater when the pilot will not light or remain lit?
If the pilot light on your Whirlpool Water Heater won't light or stay lit, try these steps: * Seat the connector firmly in its socket. * Bleed the air from the gas line. * Check with your gas utility company. * Notify the utility company to install a dirt trap in the gas line. * Locate and correct any issues. * Replace the thermostat. * Clean and locate the source of any problems, then correct them. * Contact a qualified person to reset the sensor. * Cycle the power to the water heater off and on. If the problem persists, replace the flue damper.
Why does my Whirlpool Water Heater have high operation costs?
High operation costs can be attributed to: * A thermostat set too high; lower the temperature setting. * Sediment or lime buildup in the tank; drain and flush the tank, and consider water treatment if needed. * A water heater that's too small for the demand; install an adequate heater. * Incorrect piping connections; correct the piping to ensure the dip tube is in the cold inlet. * Leaking faucets; repair the faucets. * Gas leaks; check with the utility company and repair them immediately. * Wasted hot water; advise the customer on water conservation. * Long runs of exposed piping; insulate the piping. * Hot water piping in an exposed wall; insulate the piping. * A malfunctioning flue damper seal; replace the flue damper.
What causes the flame to burn at the orifice of my Whirlpool Residential Gas?
A flame burning at the orifice may be due to: * A thermostat not functioning properly; replace the thermostat. * Low gas pressure; check with your gas utility company.
Why is my Whirlpool Water Heater slow to recover?
Slow hot water recovery can result from: * Insufficient secondary air; provide ventilation to the water heater and check the flue way, flue baffle, and burner. * A clogged flue; clean the flue and locate the source of the blockage. * Low gas pressure; check with your gas utility company. * Improper calibration; replace the thermostat. * A water heater that's too small; install an adequate heater. * Incorrect piping connections; correct the piping to ensure the dip tube is in the cold inlet. * Wasted hot water; advise the customer on water conservation.
What to do if Whirlpool Residential Gas Water Heater burner flame is too high?
If the burner flame on your Whirlpool Water Heater is too high, it may be due to an orifice that is too large. Replace it with the correct orifice.
What causes smelly water in Whirlpool Residential Gas Water Heater?
If the water from your Whirlpool Water Heater smells bad, it may be due to sulfides in the water. Replace the anode with a special anode to resolve this.
How to fix Whirlpool Water Heater burner flame that is yellow and lazy?
To address a yellow and lazy burner flame in your Whirlpool Water Heater, ensure proper ventilation to the water heater. Check with your gas utility company. Clean the burner, locate the source of the problem, and correct it. Cycle the gas control valve/thermostat off then on. If the problem persists, replace the damper. Ensure proper fresh air ventilation and clean or replace the orifice.
How to fix high operation costs of Whirlpool Residential Gas?
To reduce the high operational costs of your Whirlpool Water Heater: * Lower the temperature setting on the dial. * Drain and flush the tank, providing water treatment if needed. * Ensure you have an adequate heater for your needs. * Correct any piping issues, making sure the dip tube is properly installed in the cold inlet. * Repair any leaking faucets promptly. * Insulate the piping to minimize heat loss. Also, check with your utility provider and follow their recommendations.
General| Brand | Whirlpool |
|---|---|
| Model | Residential Gas Water Heater |
| Category | Water Heater |
| Language | English |
Critical safety warnings and important instructions for safe operation and handling of the water heater.
Detailed instructions for connecting hot and cold water lines, including recommended fittings and procedures.
A checklist to confirm the water heater is installed in a safe and compliant location, free from hazards.
Essential safety precautions and checks to perform before attempting to light the pilot flame.
Instructions for safely shutting down the water heater in emergency situations like overheating.
A critical checklist to verify the correct operation and installation of the Flame Lock® safety system components.
