Whirlpool W10323246 - User Manual

Installation Instructions
for W10323246 4-Way Vent Kit
Parts included in Kit:
1 Instruction Sheet
1 4” Diameter Vent – 305 mm (12”)
1 4” Diameter Vent – 187 mm (7.40”)
1 4” Diameter Vent – 86 mm (3.40”)
1 4” Diameter Vent – Elbow (0 degrees to 90 degrees)
2 4 3/16” Diameter Clamp
2 Plate, Cover (Metal)
2 Plugs, Side Panel (Plastic)
1 Ring, Vent
2 Screw - #8 x 1/2”
Front Load Dryer Match with Full Front Panel - Side and Bottom
Exhaust Venting
(continued)
Instruction Sheet W10337809 Rev. C 12/11
1. Unplug dryer or disconnect power.
NOTE: For Gas Dryer application, turn off gas supply using the
shut-off valve that supplies the dryer. Disconnect flexible gas
supply line connected to rear of dryer.
2. Remove dryer top by first removing the two (2) screws from
the rear of the dryer. See Figure 1.
WARNING
Electrical Shock
Hazard
Disconnect power before servicing.
Failure to do so can result in death
or electrical shock.
Replace all parts and panels before
operating.
figure 1


— 1 —
Tool and Accessories required:
• 1/4” Socket and Ratchet Wrench
• 1/4” Nut Driver
• 5/16” Nut-Driver
• Flat-Head Screwdriver
• Phillips-Head Screwdriver
• Hammer
• Pliers
• 1/8” Drill Bit
• Drill
• Cold Chisel
• File, Round
Procedure for Dryer Disassembly
To Gain Access to Inside of Dryer for Installation of Optional
Exhaust Venting
3. Remove dryer top by sliding top toward rear of dryer and lift
to remove. See Figure 2.
figure 2
4. Remove console by first removing two (2) screws (one from
each side of console) at location as shown in Figure 3.
figure 3



5. Disconnect drum light and main console connectors as shown
in Figure 4 located on top right front side of dryer. Lift up on
console and tilt assembly forward to remove console.
figure 4







Summary

Dryer Disassembly

Safety Precautions

Critical safety warnings regarding electrical shock and proper servicing procedures.

Remove Dryer Top Panel

Instructions for removing the dryer's top panel by unscrewing it from the rear.

Remove Console Assembly

Steps to remove the front console assembly by detaching screws and connectors.

Front Panel and Bulkhead Removal

Remove Front Panel Assembly

Instructions for removing the front panel assembly by detaching screws and lifting off tabs.

Remove Bulkhead Assembly

Steps to remove the bulkhead assembly by detaching screws and disconnecting clips.

Disconnect Harnesses and Sensor

Procedure for disconnecting the moisture sensor and main harness connectors.

Internal Component Removal

Remove Console Mounting Bracket

Instructions for removing the console mounting bracket screws.

Remove Drum and Existing Vent

Steps to remove the dryer drum, belt, and existing exhaust vent.

Venting Procedure

Bottom Exhaust Venting

Detailed steps for configuring the dryer for bottom exhaust venting.

Left Side Exhaust Venting

Instructions for preparing the dryer for left side exhaust venting, including knockout removal.

Right Side Exhaust Venting

Instructions for preparing the dryer for right side exhaust venting, including knockout removal.

Completing Dryer Installation

Reassemble Dryer Components

Guidance on reassembling the dryer and connecting the vent tubes and assemblies.

Reassemble Front Panel and Console

Steps for reattaching the front panel, door, console, and associated wiring.

Final Connections and Checks

Procedure for connecting power, performing final checks, and ensuring safe operation.

Whirlpool W10323246 Specifications

General

Category	Laundry Accessories
Part Number	W10323246
Brand	Whirlpool
Material	Rubber
Diameter	4 inches
Color	Silver
Model Number	W10323246
Length	72 inches