Whirlpool WFE 2B19 - User Manual

Questions and Answers

D
Deanna HendricksAug 13, 2025
Why won't my Whirlpool WFE 2B19 Dishwasher start or respond to commands?
- J
  Jason RomeroAug 13, 2025
  Your Whirlpool Dishwasher might not start or respond to commands due to several reasons: * It may not be properly plugged in; ensure the plug is fully inserted into the socket. * There might be a power outage; press the START/Pause button to resume the cycle. * The dishwasher door might not be completely closed; push the door firmly until you hear a click. * The cycle may have been interrupted by opening the door for more than 4 seconds; close the door and press the START/Pause button. * If it's unresponsive, try switching the appliance off and on again, or unplug it for a minute and then plug it back in.
R
Ronald JacksonAug 17, 2025
What to do if my Whirlpool WFE 2B19 Dishwasher is not filling with water and all the LEDs are blinking?
- M
  mathiskennethAug 17, 2025
  If your Whirlpool dishwasher isn't filling with water and all the LEDs are blinking rapidly, it could be due to: * No water in the water supply or the tap is closed; make sure there is water in the water supply and the tap is running. * The inlet hose is bent; ensure the inlet hose is not bent, then reprogram the dishwasher and reboot it. * The sieve in the water inlet hose is clogged; after verification and cleaning, turn the dishwasher off and on, then restart a new program.
S
sheenamorganAug 21, 2025
Why won't my Whirlpool Dishwasher drain?
- J
  John BrownAug 21, 2025
  If your Whirlpool Dishwasher won’t drain, it could be due to a few reasons: * The wash cycle hasn't finished yet; wait until it completes. * The drain hose is bent; check that it is not bent. * The sink drain pipe is blocked; clean the sink drain pipe. * The filter is clogged with food residues; clean the filter.
L
lindsaygrayAug 25, 2025
Why are my dishes not clean after using my Whirlpool WFE 2B19 Dishwasher?
- A
  Arthur StevensAug 25, 2025
  If your dishes aren't clean after a cycle in your Whirlpool Dishwasher, consider these potential causes: * The crockery may not have been arranged properly; arrange the crockery correctly. * The spray arms may be hindered by the dishes; arrange the crockery correctly. * The wash cycle might be too gentle; select an appropriate wash cycle. * Too much foam might have been produced due to incorrect detergent usage. * The rinse aid compartment cap may not be shut correctly; ensure it is closed. * The filter may be soiled or clogged; clean the filter assembly. * There might be no salt; fill the salt reservoir.
A
Angela VazquezAug 28, 2025
How to reduce excessive noise from my Whirlpool WFE 2B19?
- V
  vmarshallAug 28, 2025
  Excessive noise from your Whirlpool Dishwasher can be due to: * Dishes rattling against each other; position the crockery correctly. * Too much foam being produced; ensure the detergent is measured correctly and is suitable for dishwashers. Restart the dishwasher by pressing the DRAIN button and run a new program without detergent.
T
Timothy MeyerSep 1, 2025
What to do if Whirlpool Dishwasher finishes the cycle prematurely?
- D
  Desiree WilliamsSep 1, 2025
  If your Whirlpool Dishwasher is finishing cycles too early, it might be because: * The drain hose is positioned too low or siphoning into the home sewage system; check if the end of the drain hose is at the correct height and check for siphoning. Install an air admittance valve if necessary. * There is air in the water supply; check the water supply for leaks or other issues.
H
hayesrobertSep 4, 2025
Why is the salt indicator lit on my Whirlpool Dishwasher?
- J
  jacquelinemiddletonSep 5, 2025
  The salt indicator on your Whirlpool Dishwasher may be lit because the salt reservoir is empty. After refilling, the indicator may remain lit for several wash cycles. Refill the reservoir with salt and adjust water hardness.
K
Kathryn GibsonSep 8, 2025
Why is the rinse aid indicator lit on my Whirlpool Dishwasher?
- J
  James DiazSep 9, 2025
  The rinse aid indicator on your Whirlpool Dishwasher is lit because the rinse aid dispenser is empty. After you refill it, the indicator might stay on for a few wash cycles. Refill the dispenser with rinse aid.

Summary

First Time Use: Salt, Rinse Aid, and Detergent

Filling Salt Reservoir

Instructions for filling the salt compartment for water softening.

Setting Water Hardness

Guide to configuring the appliance for local water hardness levels.

Filling Rinse Aid Dispenser

Steps to refill the rinse aid compartment for improved drying.

Filling Detergent Dispenser

Instructions for correctly filling the detergent compartment.

Program Selection Guide

Program Overview Table

Chart detailing programs, drying phase, options, duration, water, and energy consumption.

Dishwasher Options and Functions

Product Identification

Initial Setup: Salt, Rinse Aid, Detergent

Water Hardness Configuration

Steps to set the water hardness level for optimal softener performance.

Wash Program Guide

Program Comparison Table

Table comparing programs by duration, water, and energy consumption.

Program Comparison

Table comparing programs by duration, water, and energy consumption.

Program Descriptions

Detailed Program Explanations

Wash Cycle Customization

Product Description

First Use: Salt, Rinse Aid, Detergent

Salt Reservoir Management

Filling the salt reservoir and setting water hardness.

Salt Reservoir and Water Hardness

Filling the salt reservoir and setting water hardness.

Rinse Aid Dispenser

Instructions for refilling and adjusting rinse aid dosage.

Rinse Aid Dispenser Management

Instructions for filling and adjusting rinse aid dosage.

Detergent Dispenser

Guide for filling the detergent dispenser.

Wash Program Reference

Program Explanations

Options and Functions

Product Presentation

Care and Maintenance

Filter Assembly Cleaning

Spray Arm Cleaning

Water Inlet Hose Cleaning

Troubleshooting Common Issues

Problem;Solution Guide

A table listing common dishwasher problems and their solutions.

Whirlpool WFE 2B19 Specifications

General

Door color	White
Cord length	1.3 m
Control type	Buttons
Product size	Full size (60 cm)
Tub material	Stainless steel
Built-in display	No
Inlet hose length	1.55 m
Outlet hose length	1.5 m
Appliance placement	Freestanding
Cutlery compartment type	Basket
Upper basket adjustable height	Yes
Current	10 A
Connected load	1900 W
AC input voltage	220 - 230 V
AC input frequency	50 Hz
Power consumption (off)	0.5 W
Water consumption per cycle	11 L
Energy consumption per cycle	1.04 kWh
Drying class	A
Annual water consumption	3080 L
Annual energy consumption	295 kWh
Cycle time	190 min
Noise level	49 dB
Drying system	Static
Delay start (max)	8 h
Dishwashing programs	Eco, Intensive, Pre-wash, Quick
Number of place settings	13 place settings
Number of washing programs	5
Package depth	675 mm
Package width	650 mm
Package height	910 mm
Package weight	49000 g

Weight and Dimensions

Width	600 mm
Height	850 mm
Weight	47000 g
Installation compartment depth	570 mm
Installation compartment height (max)	900 mm
Installation compartment height (min)	820 mm