Why “Sd” (Excess suds) appears on my Whirlpool WFW81HEDW Washer?
If the “Sd” (Excess suds) appears in the display of your Whirlpool washer, it means there are excessive suds in the washer and it is running a suds reduction routine. Allow the washer to continue. Make sure to use only HE detergent, always measure the detergent, and base the detergent quantity on the load size, following the detergent manufacturer’s instructions.
What to do if Whirlpool Washer leaking from door?
If the water or suds are leaking from the door or rear of the Whirlpool Washer cabinet, only use HE detergent. Suds from regular detergents can cause leaking from the door or rear of the cabinet. Always measure detergent and follow the manufacturer’s directions based on your load requirements. Periodically clean the underside of the glass window to avoid potential leaks. Water can drip off the inside of the door when the door is opened after the start of a cycle; this is normal for an HE front load washer. The washer senses load sizes and adds the correct amount of water for optimal cleaning.
How to clear error code on Whirlpool WFW81HEDW Washer?
If an error code appears in the display of your Whirlpool washer, once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.
What to do if F# E# code appears on Whirlpool Washer display?
If the F# E# code appears on the Whirlpool Washer display (other than described above), it indicates a system error. To resolve this, touch POWER once to clear the code, and then touch POWER again to restart the washer. If the code reappears, it is recommended to call for service.
Why Lo FL or F8 E1 error appears on Whirlpool WFW81HEDW?
If the Lo followed by FL or F8 followed by E1 (water supply error) appears on the Whirlpool Washer display, check for proper water supply. The unit will drain for 8 minutes while the door remains locked. When complete, touch POWER once to clear the code, then touch POWER again to restart the washer. If the code appears again, call for service. Ensure both hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are on. Check if the inlet valve screens on the washer may be clogged. Remove any kinks in the inlet hose. If used, auto shut off connectors and hoses must be properly installed and in working order.
What does F9 E1 error mean on Whirlpool WFW81HEDW?
If the F9 followed by E1 (drain pump system error) appears on the Whirlpool Washer display, check the plumbing for correct drain hose installation. Ensure the drain hose does not extend into the standpipe farther than 41? 2" (114 mm). Check the drain hose for proper installation, and make sure it is not kinked, pinched, or blocked. Remove any clogs from the drain hose. Use the drain hose form and securely attach it to the drainpipe or tub. Lower the drain hose if the end is higher than 96" (2.4 m) above the floor. Use only HE detergent, always measure detergent, and follow the manufacturer’s directions based on load size and soil level.
What does “rL” mean on Whirlpool WFW81HEDW display?
If the “rL” (remove load) appears in the display of your Whirlpool Washer, it means a load was detected in the drum during the Clean Washer with affresh® cycle. Remove items from the washer drum and restart the Clean Washer with affresh® cycle.
Why my Whirlpool Washer making error beeps?
If the Whirlpool Washer is making error beeps, it may be because the door has not been opened and closed for at least 3 cycles. This code may appear when the washer is first turned on. Open and close the door to clear the display.
What to do if F5 E2 error appears on Whirlpool WFW81HEDW?
If the F5 followed by E2 (door will not lock) appears on the Whirlpool Washer display, touch POWER to cancel the cycle. Make sure the door is closed completely and latching. Check for items in the washer drum that may be keeping the door from closing completely.
Why my Whirlpool WFW81HEDW beeps when I touch START?
If the Whirlpool Washer beeps when START is touched, it means the door is not closed. Close the door completely.
General| Style | front load |
|---|---|
| Color | white |
| Washer Capacity | 4.2 cubic feet |
| Noise level | yes |
| Control Panel | digital |
| Delay Start / End | yes |
| Steam | no |
| Annual Energy Consumption | 145 kilowatt hours |
Weight and Dimensions| Depth | 33.13 inches |
|---|---|
| Height | 38.75 inches |
| Width | 27 inches |
| Net Weight | 250 pounds |
To Next Page