Whirlpool WSIC 3M17 - User Manual

To Next Page

ENQuick Guide

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please register

your appliance on: www.whirlpool.eu/register

CONTROL PANEL

FIRST TIME USE

Before using the appliance carefully read Safety Instructions

guide.

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and

pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-

bration. The sensor calibration can increase program duration up to 20 min.

PROGRAMS TABLE

PLEASE SCAN THE QR CODE ON YOUR

APPLIANCE IN ORDER TO HAVE MORE

DETAILED INFORMATION

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and on

the machine’s functional components.

• It is mandatory that the salt reservoir never be empty.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher and must be

lled when the SALT REFILL indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the reservoir cap

(anticlockwise).

2. Position the funnel (see gure) and ll the salt reservoir

right up to its edge (approximately 1 kg); it is not unu-

sual for a little water to leak out.

3. Only the rst time you do this: ll the salt reservoir

with water.

4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get into

the container during the wash program (this could damage the water

softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the proce-

dure before the beginning of the washing cycle to avoid corrosion.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse

aid dispenser A should be lled when the

RINSE AID REFILL indicator light in the con-

trol panel is lit.

NEVER pour the rinse aid directly into the

appliance tub.

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device C. Introduce the

detergent into the dry dispenser D only. Place the amount of detergent for

pre-washing directly inside the tub.

If all-in-one detergents are used, we recommend using the TABLET button,

because it adjusts the program so that the best washing and drying results

are always achieved.

Usage of detergent not designed for dishwashers may cause

malfunction or damage to the appliance.

WATER SOFTENING SYSTEM

Water softener automatically reduces water hardness, consequently pre-

venting scale buildup on heater, contributing also to better cleaning e-

ciency. This system regenerates itself with salt, therefore it is required

to rell salt container when empty.

Frequency of regeneration depends on water hardness level setting - regen-

eration takes place once per 6 Eco cycles with water hardness level set to 3.

Regeneration process starts in nal rinse and nishes in drying phase, be-

fore cycle ends.

• Single regeneration consumes: ~3.5L of water;

• Takes up to 5 additional minutes for the cycle;

• Consumes below 0.005kWh of energy.

1 2 3 4 5 6 7 8 9 10

1. ON-OFF/Reset button with indicator light

2. Program selection button

3. Salt rell indicator light

4. Rinse Aid rell indicator light

5. Program number and delay time indicator

6. Tablet indicator light

7. Display

8. Multizone indicator lights

9. Multizone button

10. Delay button

11. START/Pause button with indicator light / Tablet (Tab)

Program Programs description

Drying

phase

Available

options

Duration

of wash

program

(h:min)

**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

Eco 50°- Eco program is suitable to clean normally soiled tableware.

that for this use. it is the most ecient program in terms of its com-

bined energy and water consumption. and that it is used to assess

compliance with the EU Ecodesign legislation.

4:00 9.0 0.84

Sense 50°- 60°- For normally soiled dishes with dried food

residues. Senses the level of soiling on the dishes and adjusts the

program accordingly. When the sensor is detecting the soil level an

animation appears in the display and the cycle duration is updated.

1:20 - 3:00 7.0 - 14.0 0.70 - 1.10

Intensive 65° - Program recommended for heavily soiled crockery. espe-

cially suitable for pans and saucepans (not to be used for delicate items).

2:40 17.0 1.30

Crystals

45° -

Program for delicate items. which are more sensitive

to high temperatures. for example glasses and cups.

1:40 12.0 1.00

Rapid 30’

50° -

Program to be used for half load of lightly-soiled

dishes with no dried food residues. Does not have drying phase.

0:30 9.0 0.50

Prewash - Use to refresh crockery planned to be washed later. No

detergent to be used with this program.

0:10 4.5 0.01

Main Page

Need help?

Do you have a question about the Whirlpool WSIC 3M17 and is the answer not in the manual?

Whirlpool WSIC 3M17 Specifications

General

Appliance placement	Freestanding
Size	60 cm
Control panel colour	Black
Number of Washing Programs	6
Adjustable Upper Basket Height	Yes
Water Consumption per Cycle	9.5 L
Delay Start	Yes
Half Load Option	Yes
Number of Place Settings	13
Washing Programs	Eco, Intensive, Normal, Rapid