Whirlpool WSIC 3M27 C

Questions and Answers

D
Diana JonesJul 28, 2025
What causes a Whirlpool WSIC 3M27 C to not clean dishes properly?
- R
  Ryan DavisJul 28, 2025
  Several factors can cause your Whirlpool Dishwasher to not clean dishes effectively: * Improper arrangement of crockery. Make sure to arrange the crockery correctly. * Spray arms being hindered by dishes. Ensure the spray arms can rotate freely. * Wash cycle being too gentle. Select a more appropriate wash cycle. * Excessive foam production due to incorrect detergent usage. Ensure the detergent is measured correctly and is suitable for dishwashers. * Rinse aid compartment cap not shut correctly. Make sure the cap of the rinse aid dispenser is closed. * Soiled or clogged filter. Clean the filter assembly. * Lack of salt. Fill the salt reservoir.
T
Thomas KennedyAug 1, 2025
How to fix a Whirlpool WSIC 3M27 C that is excessively noisy?
- R
  rjensenAug 1, 2025
  If your Whirlpool Dishwasher is excessively noisy, here are a couple of potential causes and solutions: * Dishes rattling against each other: Position the crockery correctly. * Excessive foam production: The detergent has not been measured out correctly or is unsuitable for dishwashers. Restart the current cycle without adding any detergent by switching OFF the dishwasher, then switch it on again, select a new program, press START/Pause and close the door within 4 seconds.
M
Michele ThomasAug 6, 2025
Why does my Whirlpool WSIC 3M27 C Dishwasher not fill with water?
- D
  Douglas RamosAug 6, 2025
  If your Whirlpool Dishwasher isn't filling with water, consider these possibilities: * Check that there is water in the water supply and that the tap is open. * Ensure that the inlet hose is not bent. Reprogram the dishwasher and reboot it after correcting the hose. * The sieve in the water inlet hose may be clogged; clean it. After cleaning, turn the dishwasher off and on, then restart a new program.
M
Michelle YoderAug 10, 2025
What to do if my Whirlpool Dishwasher finishes cycle prematurely?
- R
  Richard LopezAug 10, 2025
  If your Whirlpool Dishwasher is ending its cycle too early: * Check that the drain hose is placed at the correct height and is not siphoning into the home sewage system. Install an air admittance valve if necessary. * Check the water supply for leaks or other issues that could be letting air inside.
R
Robert HolmesAug 14, 2025
Why is the salt indicator lit on my Whirlpool WSIC 3M27 C Dishwasher?
- B
  Brooke WilliamsAug 14, 2025
  The salt indicator on your Whirlpool Dishwasher may be lit because the salt reservoir is empty. Refill it with salt. Note that the salt indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness according to the table.
M
Michael AllenAug 18, 2025
What does it mean when the rinse aid indicator is lit on my Whirlpool WSIC 3M27 C?
- J
  Joseph ChaseAug 18, 2025
  The rinse aid indicator on your Whirlpool Dishwasher lights up when the rinse aid dispenser is empty. Refill the dispenser with rinse aid. The indicator may remain lit for several wash cycles after refilling.
D
Dana MartinezAug 23, 2025
What to do if my Whirlpool Dishwasher starts or does not respond to commands?
- E
  epaceAug 23, 2025
  If your Whirlpool Dishwasher isn't starting or responding, here are a few things to check: * Ensure the appliance is properly plugged into the socket. * If there was a power outage, open the dishwasher door, press the START/Pause button, and close the door within 4 seconds (the dishwasher won't restart automatically after a power failure for safety reasons). * Make sure the dishwasher door is fully closed until you hear a 'click'. * If the door was opened for more than 4 seconds during a cycle, press START/Pause and close the door within 4 seconds. * If the display shows 9 or 12 and the On/Off LED is blinking rapidly, switch the appliance off and on again after one minute. If the problem continues, unplug it for one minute and then plug it back in.

Summary

First Time Use

Filling the Salt Reservoir

Instructions on how to fill the salt reservoir to prevent limescale.

Filling the Rinse Aid Dispenser

Guidance on filling the rinse aid dispenser for better drying.

Adjusting Rinse Aid Dosage

Setting Water Hardness

Filling the Detergent Dispenser

Care and Maintenance

Cleaning the Filter Assembly

Instructions for regular cleaning of the filter assembly.

Cleaning the Spray Arms

Guidance on cleaning the spray arms to ensure proper water flow.

Water Softening System

Troubleshooting Guide

Salt Indicator Lit

Rinse Aid Indicator Lit

Dishwasher Not Starting

Troubleshooting steps for when the dishwasher does not respond.

Dishwasher Not Draining

Causes and solutions for issues related to the dishwasher not draining.

Dishwasher Makes Noise

Dishes Not Clean

Troubleshooting steps for when dishes are not cleaned properly.

Dishwasher Does Not Fill

Causes and solutions for the dishwasher not filling with water.

Dishwasher Finishes Prematurely

Whirlpool WSIC 3M27 C Specifications

General

Door color	Not applicable
Water fill	Cold, Hot
Cord length	1.3 m
Control type	Buttons
Product size	Slimline (45 cm)
Built-in display	Yes
Inlet hose length	1.55 m
Outlet hose length	1.5 m
Appliance placement	Fully built-in
Control panel color	Silver
Cutlery compartment type	Basket
Child lock	No
Remaining time indication	-
Current	10 A
Connected load	1900 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Power consumption (off)	0.5 W
Water consumption per cycle	9 L
Energy consumption per cycle	0.74 kWh
Cycle time	240 min
Noise level	47 dB
Delay start (max)	12 h
Dishwashing programs	Eco, Intensive 65°C, Pre-wash
Number of place settings	10 place settings
Number of washing programs	6
Maximum hot water supply temperature	60 °C
Drying class	A
Annual water consumption	2520 L
Annual energy consumption	212 kWh
Package depth	675 mm
Package width	500 mm
Package height	890 mm
Package weight	31600 g