WinZo AN5024 - User Manual

To Next Page

WINZO

WINZO WINZO

WINZO

Installation Instruction

For One Piece Toilet (Side Flush)

IMPORTANT!

PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE

The toilet must be installed by a fully insured and licenced plumber only.

Also be sure the installation conforms to local plumbing and building codes.

TOOLS REQUIRED FOR INSTALLATION

Soft Cloth

or Blanket

Silicone Silicone/

Caulk Gun

Tape

Measure

Pencil/Marker

Knife

Adjustable

Wrench

Screwdriver

Level

Putty Knife

INSTALL NEW TOILET

REMOVE OLD TOILET Shut off main water supply prior to installation!

1. Shut off water supply line. If you do not have shut-off valve near the toilet shut off main water supply line.

2. Flush the old toilet and make sure that tank is empty.

3. Disconnect and remove water supply line connected to the toilet's tank.

4. Remove old toilet, bolts, nuts from the closet flange.

5. Clean closet flange area from old wax ring and putty sealant using putty knife from the base area.

6. Clean any remaining debris and wipe any water at the installation area

7. Temporarily plug flange on a floor with a flange plug or towel to prevent gasses from escaping

IMPORTANT! The mounting surface area must be clean, dry,

and leveled prior to installation of the new toilet!

NOTE! Inspect the existing closet flange for damages. If

damaged, replace it to new flange before proceeding to the

installation

Thanks for your selecting our products. To ensure this product is installed properly, please read these instructions carefully before you begin.

1. If it is a new bathroom, install water supply ,shut-off valve,

and toilet flange as necessary to conform to the roughing-in

dimensions.

Bathroom

Wall

Bathroom

Floor

Closet Flange

12"

Rough-in

Figure 1

Step 1 Step 2

90º

3. Cover the floor with the soft-cloth blanket.

Carfeully turn the toilet on it’s side or

upside-down on the blanket. Install wax ring on

the toilet outlet.(see Figure 2)

Figure 2

4. Lift and carefully put the toilet over the

closet flange so the closet bolts can go through

the mounting holes in the toilet's base. Apply

full body weight to rim of bowl for proper

gasket seal.(see Figure 3)

5. Install bolt cap bases, washers,nut

and bolt cap over the closet bolts via

the opening holes on both side of

bowl. Do not tighten the nuts. It may

and will cause damage to the toilet's

ceramic base. Then cover the opening

holes with supplied plastic cover. (see

Figure 4)

6. Connect the water supply line,and

turn on the water. Flush several times,

check for leaks. (see Figure 5)

7. If necessary, adjust the water level

in the water tank. Turn the adjusting

screw clockwise to raise the water or

Turn the screw counter-clockwise to

reduce water. (see Figure 5)

8. Make sure the refill tube is

properly inserted into the

overflow pipe of the flush valve.

Refill tube should be positioned

higher than water level. (see

Figure 6)

9. Carefully put the tank lip on the

tank. Install the supplied toilet seat.

(see Figure 7)

10. Apply the silicone around the

base of the toilet. When the silicone

is dry, check for leaks for the next

several days (see Figure 7)

2. Inser 2 floor bolts inside of the toilet flange and slide the bolts

through the holes and align bolts horizontaly. (see Figure 1)

Figure 3

RIGHTWRONG

Water

Level

Figure 6

Figure 7

Bolt cap

Nut

Bolt Cap Base

Washer

Plastic cover

Figure 4

Model:AN5024 (WZ5024)

WinZo

(Toilet seat installation see Page 3)

Refill Tube

Adjusting Screw

Water Line

Supply Line

Shut-off Valve

Overflow Pipe

Figure 5

1/3

4”

Need help?

Do you have a question about the WinZo AN5024 and is the answer not in the manual?

This document provides installation, troubleshooting, care, and warranty information for the WinZo AN5024 (WZ5024) One Piece Toilet with a side flush mechanism.

Function Description:

The WinZo AN5024 (WZ5024) is a one-piece toilet designed for bathroom use, featuring a side flush mechanism. Its primary function is to provide a sanitary waste disposal system, utilizing a water-based flushing action. The toilet is designed for easy installation and maintenance, with specific instructions provided for both new installations and replacement of old toilets. The side flush design integrates the flushing mechanism into the side of the tank, contributing to its one-piece aesthetic.

Important Technical Specifications:

While specific dimensions for the toilet itself are not explicitly listed, the installation instructions highlight a crucial rough-in dimension: 12 inches from the bathroom wall to the center of the closet flange. This measurement is critical for proper alignment and installation. The toilet utilizes standard plumbing connections for water supply and waste drainage. The flushing mechanism includes a refill tube, an adjusting screw for water level, and an overflow pipe. The toilet seat is designed with a quick-release feature for easy cleaning, utilizing fixing bolts, washers, a fixing base, flex-washers, and expansion fittings. The toilet's ceramic base is designed to accommodate standard closet bolts for secure floor mounting.

Usage Features:

The toilet is designed for straightforward operation. Flushing is initiated via a side-mounted mechanism. Water level in the tank can be adjusted by turning an adjusting screw: clockwise to raise the water level and counter-clockwise to lower it. The refill tube must be properly inserted into the overflow pipe and positioned higher than the water level for correct function. The toilet seat features a quick-release mechanism, allowing users to easily remove it for cleaning by depressing two release buttons. The installation process emphasizes proper sealing with a wax ring and silicone to prevent leaks and ensure hygienic operation.

Maintenance Features:

The WinZo AN5024 (WZ5024) is designed with several features to facilitate maintenance and ensure longevity.

Cleaning: For general cleaning, the manufacturer recommends using warm water with soft sponges or soft cloths. It is crucial to rinse thoroughly after cleaning and avoid leaving any chemical residue on the surface. The toilet seat's quick-release feature significantly simplifies cleaning by allowing it to be removed from the pan.
Troubleshooting: The manual provides a comprehensive troubleshooting guide for common issues such as poor flush/low flush volume and continuous water leakage in the tank. Solutions include checking the shut-off valve, adjusting water level, repositioning push button rods, cleaning the filter screen, correctly installing the refill tube, adjusting the inlet valve position, and cleaning/reassembling the flush valve and gasket.
Preventative Measures: The instructions strongly advise against using abrasive cleaners (acid, ammonia, bleach, etc.) and abrasive sponges or brushes (steel wool, wired brushes) as these can cause corrosion, finish peeling, dull surfaces, and permanent scratches. Pouring chlorine or other chemicals into the tank is also prohibited, as it can damage internal components like the fill valve and flush valve, potentially leading to floods and property damage.
Installation for Maintenance: The installation process itself includes steps that contribute to long-term maintenance, such as inspecting the existing closet flange for damage and replacing it if necessary, ensuring the mounting surface is clean, dry, and level, and applying silicone around the base of the toilet to prevent leaks.
Warranty: The vitreous china components are guaranteed for five years from the date of purchase, while internal valving and plastic components are guaranteed for one year. The warranty is subject to conditions including professional installation by a licensed plumber, home use only, manufacturing fault, absence of additives in the tank, use of only soft sponges/cloths for cleaning, and proof of purchase. This warranty structure encourages proper installation and maintenance practices to ensure product longevity.

In summary, the WinZo AN5024 (WZ5024) toilet is a one-piece unit designed for ease of installation, user-friendly operation, and simplified maintenance, with clear guidelines to ensure its durability and performance.

WinZo AN5024 Specifications

General

Brand	WinZo
Model	AN5024
Category	Toilets
Language	English

Related product manuals

WinZo WZ5081

2 pages