Wood-mizer LT25L - User Manual

Questions and Answers

A
Anthony CastroSep 23, 2025
Why pump motor runs with no response from cylinders on Wood-mizer LT25L?
- M
  Michael TaylorSep 23, 2025
  If the pump motor runs with little or no response from the cylinders on your Wood-Mizer Saw, test the battery and replace or recharge as necessary if the battery is low or dead. Remove the motor from the pump and inspect it, repairing or replacing as necessary if the pump motor is defective. Check the ground connection between the pump and saw frame if there is a poor ground connection.
S
saundersmelissaAug 25, 2025
What to do if blade does not track right on Wood-mizer Saw?
- B
  bradleyrobertAug 25, 2025
  If the blade on your Wood-mizer Saw does not track right, readjust on the Drive Wheel if the cant adjustment is incorrect. Replace B-57 belts if flat or worn belts are the cause.
J
Jennifer RussellAug 25, 2025
Why do drive belts wear prematurely on Wood-mizer LT25L Saw?
- L
  Lisa GutierrezAug 26, 2025
  If the drive belts on your Wood-mizer Saw wear prematurely, align the pulleys if the engine/motor and drive pulleys are out of alignment. See Section 4.6 for instructions.
J
Jonathan JonesAug 27, 2025
How to prevent Wood-mizer LT25L Saw blades from dulling quickly?
- C
  Connie RomanAug 27, 2025
  To prevent Wood-mizer Saw blades from dulling quickly, ensure you clean or debark logs, especially on the entry side of the cut. If grinding teeth, grind just enough metal to restore sharpness and use water/coolant. Also, ensure proper sharpening techniques are used.
J
Jessica MorrisonAug 27, 2025
What to do if Wood-mizer LT25L Saw makes wavy cuts?
- Z
  zstevensAug 27, 2025
  If your Wood-mizer Saw is making wavy cuts, try slowing the feed rate. Resharpen the blade, ensuring you consult the Sharpener Manual. Adjust the blade guides, use water lube to address sap buildup, and resharpen and reset the blade to correct tooth set issues.
M
michaelrobinsonSep 15, 2025
How to fix fluid leak around pump box of Wood-Mizer Saw?
- M
  millerheatherSep 15, 2025
  To address a fluid leak around the pump box of your Wood-Mizer Saw, thoroughly wipe the pump to locate the source of the leak. You may need to unbolt the pump to clean behind it.
W
William NelsonSep 12, 2025
What to do if blade does not stop immediately after disengaging on Wood-mizer Saw?
- G
  glopezSep 13, 2025
  If the blade on your Wood-mizer Saw does not stop immediately after disengaging, adjust the brake strap.
R
Richard OliverSep 14, 2025
Why does Wood-mizer LT25L Saw cut out and then work again?
- B
  beth54Sep 14, 2025
  If everything works and then cuts out and works again on your Wood-Mizer Saw, check the connection in the battery.
C
Carmen EdwardsSep 5, 2025
Why does height adjustment jump on Wood-mizer LT25L Saw?
- M
  Michael CollinsSep 5, 2025
  If the height adjustment on your Wood-mizer Saw jumps or stutters, lubricate the mast track surface. Adjust the up/down chain, adjust the vertical wear pads if they are too tight and adjust belts if drive belt(s) loose.
C
cesarmercadoSep 2, 2025
Why are boards thick or thin on ends or middle when using Wood-mizer LT25L Saw?
- E
  eddiescottSep 3, 2025
  If boards cut by your Wood-mizer Saw are thick or thin on the ends or middle, take equal cuts off opposing sides after the log has been squared. Remove a board, repeat, keeping the heart in the middle of the cant, making it your last cut. Resharpen and reset the blade if there's a set in the teeth. Realign the sawmill if the bed rails are misaligned.