Woodward GS16 - User Manual

Woodward Publication 26889 page 1
Installation Procedure Supplement
Manual 26889 (Revision NEW, 5/2015)
GS16 Gas Metering System
See manual 26514 for complete installation, operation, maintenance, and certification
information. Publications can be found on our website at www.woodward.com/publications.
Important Definitions
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
 DANGER—Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
 WARNING—Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
 CAUTION—Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
 NOTICE—Indicates a hazard that could result in property damage only (including damage to the control).
 IMPORTANT—Designates an operating tip or maintenance suggestion.
The engine, turbine, or other type of prime mover should be equipped with an
overspeed shutdown device to protect against runaway or damage to the prime
mover with possible personal injury, loss of life, or property damage.
The overspeed shutdown device must be totally independent of the prime mover
control system. An overtemperature or overpressure shutdown device may also
be needed for safety, as appropriate.
Read this entire manual and all other publications pertaining to the work to be performed before
installing, operating, or servicing this equipment. Practice all plant and safety instructions and
precautions. Failure to follow instructions can cause personal injury and/or property damage.
This publication may have been revised or updated since this copy was produced. To verify that
you have the latest revision, check manual
26455, Customer Publication Cross Reference and
Revision Status & Distribution Restrictions, on the publications page of the Woodward website:
www.woodward.com/publications
The latest version of most publications is available on the publications page. If your publication is
not there, please contact your customer service representative to get the latest copy.
Any unauthorized modifications to or use of this equipment outside its specified mechanical,
electrical, or other operating limits may cause personal injury and/or property damage, including
damage to the equipment. Any such unauthorized modifications: (i) constitute "misuse" and/or
"negligence" within the meaning of the product warranty thereby excluding warranty coverage
for any resulting damage, and (ii) invalidate product certifications or listings.
To prevent damage to a control system that uses an alternator or battery-charging
device, make sure the charging device is turned off before disconnecting the battery
from the system.
To prevent damage to electronic components caused by improper handling, read
and observe the precautions in Woodward manual
82715, Guide for Handling and
Protection of Electronic Controls, Printed Circuit Boards, and Modules.

Summary

Important Safety Information and Definitions

Safety Alert Symbol and Hazard Definitions

Defines the safety alert symbol and hazard levels (DANGER, WARNING, CAUTION, NOTICE).

Overspeed Shutdown Device Warning

Highlights the mandatory independent overspeed shutdown device for prime movers.

General Safety Precautions and Revision Verification

Emphasizes reading all manuals and verifying the latest revision status.

Handling and Electrical Connection Notices

Covers notices for battery charging devices and electronic component handling.

Service and Support Procedures

Replacement and Repair Programs

Details premium replacement/exchange and flat rate repair/remanufacture programs.

Equipment Return and Contact Information

Outlines procedures for returning equipment for repair and provides support contact details.

Regulatory Compliance and Certifications

European Compliance Directives

Lists compliance with EMC, Pressure Equipment, and ATEX directives for CE marking.

International and North American Compliance

Covers compliance with Machinery, GOST R, IECEx, and CSA certifications.

Special Conditions for Safe Use

Field Wiring, Grounding, and Interface Usage

Specifies field wiring, grounding, and restrictions for RS-232/-485 interfaces in hazardous areas.

Environmental and Handling Safety Warnings

Addresses explosion hazards, component substitution, hearing protection, surface temperatures, and fire protection.

Declaration of Conformity

Manufacturer, Model, and Directive Conformance

Identifies manufacturer, product model, and EU directives for conformity.

Applicable Standards and Third-Party Certifications

Lists relevant industry standards and third-party certifications obtained.

Declaration of Incorporation

Partly Completed Machinery Compliance

Declares conformity with Directive 2006/42/EC for the product as partly completed machinery.

Essential Requirements and Technical Documentation

Lists applicable essential requirements and confirms technical documentation compilation.

Woodward GS16 Specifications

General

Brand	Woodward
Model	GS16
Category	Industrial Equipment
Language	English