Workshop Plus SmartBox 9 - Important Instructions

Important
Instructions:
1
This
Smart
Box9
has
4
indicator
lights
on
the
switch button.
When
two
or more
of
the
light
are
not
illuminated
do
not
try
and
start
a
car.
The
unit
can
still
be used
to
charge
any
mobile
or
digital
devices.
Please
charge
the unit
following
the
charging
instructions.
2.
When
using
the
Smart
Box9
to
start
a
car, it
will
normally
start
first
time.
Do
not
try
and
start
the
car more
than
three
times
continuously.
Failure
to
adhere
to
this
notice
could
result
in
damage
to
the
vehicle.
3.
Please
check
the
power
after
periods
of
inactivity
and
keep
the
unit
charged
to
ensure
maximum
performance.
4.
Please
do
not
use
the
Smart
Box9
to
charge
your
mobile devices
in
non-emergency
situations. This
will
ensure
the
Smart
Box9
will
have
enough
power
should
you
need
to start
your
car
in
an
emergency.
5.
This
Smart
Box9
is suitable
to start a
car
with
a
12v
75ah
battery.
Generally
all
cars
up
to
and
including 35
00cc
A.
Product
layout
B.
Part List
1
.
starting
power
bank
2.
home
charger
3.
micro
cable
4.
Jump
cable
battery
clamps
5.
car
charger
©
Power
indication
comparison
table:
C.
Turning
the
Smart
Box9
on
and
checking
for
power
1
.
Press the
Switch
button
once
and check
the
power
lights
are
illuminated
2.
to
activate the
LED
light,
press
and hold down the switch
button
for
three
seconds
The
3
modes
of
LED will
appear
in
the
following
sequence
Continual,
slow
flashing,
strobe,
red/blue
flashing,
off.
3.
This
Smart
Box9
has
an
intelligent
shutdown,
when there is
no
connectivity,
it
will
shutdown
automatically
after
20
seconds
to
conserve
power.
4
Check
the
lights
for
the
remaining
power
When
4
lights
are
on,
power
=
75-100%
When
3
lights
are
on,
power
=
50-75%
When
2
lights
are
on,
power
=
25-50%
When
1
light
is
on,
power
=
10-25%
If
no
lights
are
on,
power
=
0%
When
charging,
the
lights
will
flash
to
indicate how much
charge
the
Smart
Box9
has taken
When the
1st
light
flashes,
the
power
is under
25%
When
the
2nd
light
flashes,
the
power
is
between
25-50%
When the
3rd
light
flashes,
the
power
is between
50-75%
When
the
4th
light
flashes,
the
power
is
between
75-100%
When all
4
lights
are
on
the unit is
fully
charged.
[03]
Pmcrrifcfcrigfc
oooo oooo
•ooo
•
•OO
•••0
• •••
C.nescn4t
0% 10% <25% 50% 75% 100%
O
Off
Oflash#
on
D.
Charging
the
Smart
Box9
Please
use
the home
charger
or car
charger
to
charge
the
Smart
Box9.
When all
4
lights
are on
the unit is
fully
charged.
Please
disconnect the unit
to
save
the
power.
E.
How
to
jump
start
a
12v
car
1
.
Turn the
Smart
Box9
on
and check that the unit is
at
least
75%
charged
i.e
3
or
4
lights
are on.
2.
Connect
the
battery
clamps
to
the
car
battery.
Red
battery
clamp
to
the
positive
terminal and the black
battery
clamp
to
the
negative
terminal
3.
Insert
the
plug
of
the
battery
clamps
into
the
Smart
Box9
4.
Start
the
car
with
the
ignition key.
5.
The
car
should
start
first
time,
once
the
engine
is
running
disconnect the
plug
from
the
Smart
Box9
within
15
seconds
6.
Remove the
clamps
from
the
battery
F.
Chare
1.
Choo
be
char
2.
Plug
t
socket
<
3.
Turn
»
will
sta
G.
Spei
Capaity
:
SIZE
:
1
Weight
:
Output
:
Input
:
1
Full cha
Starting
Peak
cu
Operatir
Storage