Workspace WA6-NO - User Manual

1
TRAVEL ELECTRIC AND MANUAL SIT-TO-STAND SYSTEMS
USER GUIDE AND TROUBLESHOOTING
Control Panel
See figure 1 to identify the buttons of the control panel.
Operation:
UP: Touch and hold the UP button to move the desk up to the desired height. Release to stop.
DOWN: Touch and hold the DOWN button to move the desk down to the desired height. Release to stop.
DISPLAY SCREEN: Displays the height or error codes.
M1: Touch and hold the M1 button for 5 seconds at the desired height to save in memory.
M2: Touch and hold the M2 button for 5 seconds at the desired height to save in memory.
HOME: Touch the HOME button to move the desk to the home position of 720mm.
Note: The control panel enters sleep mode after 30 seconds. To reactivate, touch the UP or DOWN buttons.
Label
Find the label on the back of the handset. See figure 2 to identify the date of manufacture and generation
code on the label.
Figure 1: Control Panel
Figure 2: Label
Date of
Manufacture
Generation Code

Summary

Control Panel Overview

Operation

Explains the function of each button on the control panel for desk movement and memory settings.

Sleep Mode

Details the control panel's sleep mode activation after 30 seconds and reactivation method.

Label Information

Label Content

Identifies the date of manufacture and generation code found on the handset label.

Generation 1.0 Programming

Height Calibration

Describes calibrating desk height for Generation 1.0 systems by matching displayed and physical heights.

Height Limit Settings

Details setting and adjusting the maximum and current height limits for Generation 1.0 systems.

Generation 1.2 & 2.0 Programming

CMS Sensitivity

Covers adjusting Collision Mitigation System sensitivity for downward movement on Gen 1.2/2.0.

Height Calibration

Explains height calibration for Generation 1.2 and 2.0 systems, matching displayed and physical heights.

Height Limit Settings

Details setting and adjusting max height limits and current height limits for Gen 1.2/2.0.

Advanced Programming

Generation 2.0 Lower Limit

Details setting the minimum height limit for Generation 2.0 systems.

Adjust Lower Limit

Explains how to adjust the lower limit position for Generation 2.0 systems.

Generation 3.0 CMS Sensitivity

Covers adjusting Collision Mitigation System sensitivity for downward movement on Gen 3.0.

Generation 3.0 Unit of Measurement

Details changing the unit of measurement between CM and INCH for Generation 3.0.

Generation 3.0 Height Calibration

Explains height calibration for Generation 3.0 systems, matching displayed and physical heights.

Generation 3.0 Lower Limit

Details setting the minimum height limit for Generation 3.0 systems.

Maximum Height Limit Adjustment

Generation 3.0 Max Height

Details setting the desired upper limit for Generation 3.0 systems.

CMS Sensitivity Upwards

Covers adjusting Collision Mitigation System sensitivity for upward movement on Gen 3.0.

Error Codes

Generation 1.0, 1.2, 2.0 Errors

Explains troubleshooting for '00' error codes by checking connections and power.

Generation 3.0 ER1: Motor Stopped

Troubleshooting for ER1: Motor has stopped, involving power cycling.

Generation 3.0 ER2: Height Difference

Troubleshooting ER2: Over 5cm height difference between legs using CMS sensitivity.

Generation 3.0 ER3: Loose Wire

Troubleshooting ER3: Loose wire or connection by checking cables and connections.

Troubleshooting Specific Errors

Generation 3.0 ER4: Communication

Troubleshooting ER4: Communication problem by checking cables and connections.

Generation 3.0 ER5: Overloading

Troubleshooting ER5: Overloading problem by lightening the load on the desk.

HOT: Overheating Problem

Addresses the HOT error code, advising rest periods based on desk loading.

General Troubleshooting

Assembly Checks

Ensures proper assembly and connection of legs, handset, and power during boot-up.

Power and Connections

Verifies correct installation and reassembly of all plugs and cables to the control box.

Range of Movement Issues

Addresses issues where desk movement is limited, possibly due to factory pre-set limits.

Operation and Conflicts

Movement Obstructions

Checks for objects obstructing desk movement and explains CMS activation by resistance.

Resetting Desk Levels

Details how to reset desk levels to their lowest possible height by holding the DOWN button.

Desk Movement Issues

Troubleshoots short downward movement followed by upward movement due to obstructions.

Manual Desk Conflicts

Explains conflicts in manual desks and how to check gear configuration via bud visibility.

Workspace WA6-NO Specifications

General

Brand	Workspace
Model	WA6-NO
Category	Control Unit
Language	English