Xantrex xpower PowerSource 1800

Questions and Answers

S
Scott TranAug 12, 2025
What to do if Xantrex xpower PowerSource 1800 Camera Accessories shows overload shutdown?
- L
  Lacey WilsonAug 13, 2025
  If your Xantrex Camera Accessories is showing an overload shutdown, it could be due to several reasons. First, ensure that the total power consumption of the connected products is within the device's continuous power rating of 1440 W. Secondly, the AC products connected might have a surge power exceeding the device's surge capability of 2880 W, so use products within this limit. Lastly, a connected product might be damaged and should be serviced by a qualified technician.
W
williamskarlAug 16, 2025
What to do if Xantrex xpower PowerSource 1800 Camera Accessories shows over-temperature shutdown?
- P
  pedrodavisAug 16, 2025
  If your Xantrex Camera Accessories is experiencing an over-temperature shutdown, disconnect the products from the AC outlets and let the unit cool down for about 20 minutes. Make sure to clear any blockage from the fan or remove any objects covering the unit. Consider moving the unit to a cooler location and reduce the load to less than 1800 W if you need continuous operation.
T
Todd KochAug 20, 2025
What to do if Xantrex xpower PowerSource 1800 Camera Accessories has no power at the 120 VAC outlets?
- M
  Michael MilesAug 20, 2025
  If there is no power available at the 120 VAC outlets of your Xantrex Camera Accessories, it could be because the AC outlet has been overloaded or the supplementary protector has tripped. Try reducing the number of products plugged into the AC outlets. Also, check the supplementary protector at the back of the unit and reset the breaker by pushing it fully inward if necessary.
E
Emily MullinsAug 23, 2025
Why won't my Xantrex Camera Accessories turn on?
- D
  Dean ThomasAug 25, 2025
  Your Xantrex Camera Accessories might not turn on because the battery is discharged and utility power is not available at the wall outlet. Ensure that power is available at the wall outlet.
E
Edward SmithAug 27, 2025
What to do if AC utility is not available and products connected to Xantrex xpower PowerSource 1800 Camera Accessories lose power?
- L
  Leslie MorenoAug 28, 2025
  If AC utility is unavailable and products connected to your Xantrex Camera Accessories lose power, it could be due to several reasons: * The device has detected an overload condition, so ensure the connected products do not exceed the output power rating when supplying backup power. * The device has detected an over-temperature condition, so allow the unit to cool, increasing ventilation if necessary. * The device has exhausted its available battery power, so allow the unit to recharge for 15 hours before continuing use.
S
Sharon DavisAug 31, 2025
What to do if Xantrex Camera Accessories shows low voltage shutdown?
- B
  Benjamin RodriguezAug 31, 2025
  If your Xantrex Camera Accessories shows a low voltage shutdown, it is because the battery is discharged. Recharge the battery by plugging the AC power cord into a wall outlet.
M
murphymalikSep 4, 2025
What to do if Xantrex xpower PowerSource 1800 shows over-temperature warning?
- J
  Jacqueline WalkerSep 4, 2025
  If your Xantrex Camera Accessories is showing an over-temperature warning, it means the device is overheating due to poor ventilation, excessive ambient temperature, or high power demand. You should reduce the load to avoid an over-temperature shutdown. Clear any blocked fan or remove objects covering the unit, or move the unit to a cooler place.
M
Meagan McdonaldSep 8, 2025
What to do if Xantrex xpower PowerSource 1800 shows under-voltage warning?
- M
  Maria HoffmanSep 8, 2025
  If your Xantrex Camera Accessories is showing an under-voltage warning, it means the battery is nearly discharged. You should reduce the load to extend run time during backup mode. Assuming the AC power cord was unplugged and the unit turned to backup mode, when utility power is present or becomes available, recharge the battery by plugging the AC power cord into a wall outlet.

Summary

Important Safety Instructions

Electrical Hazards and Shock Prevention

Instructions to avoid electrical shock and hazards from the PowerSource 1800.

Risk of Injury or Loss of Life

Do not use with life support or medical equipment.

Explosion Hazard Warnings

Do not use where flammable fumes or gases are present.

Damage Risk and Grounded Neutrals

Avoid connecting to AC loads with grounded neutrals.

Usage Precautions

Rechargeable Appliance Compatibility

PowerSource 1800 output is modified sine wave; may damage certain equipment.

Incompatible Devices and Potential Problems

Lists appliances and products that may be damaged by the output.

Product Features Overview

Front Panel Features

Description of LEDs, screen, and buttons on the front panel.

Rear Panel Features

Description of AC outlets, surge protector, and blue LED on the rear.

Installation and Operation Guide

Safety Warnings and Usage Notes

Covers shock hazards, equipment damage cautions, and important storage notes.

Setup and Backup Power Operation

Steps for installation and explanation of the backup power feature.

AC Power Capabilities and Management

Power Consumption Limits and Backup

Details AC power capabilities and backup power limits.

Optimizing Run Time

Recommendations for maximizing run time during power outages.

Battery and Recycling Information

Battery Replacement Procedure

Information on replacing internal batteries with equivalent sealed lead acid batteries.

Environmental Recycling Guidelines

Instructions for responsible disposal of batteries and the unit.

Troubleshooting and Error Codes

Understanding Error Codes

Explanation of error codes displayed on the screen and their causes.

Problem Resolution Guide

Common problems, symptoms, and their solutions for PowerSource 1800.

Product Specifications

Electrical and General Specifications

Detailed technical specs including output, voltage, temperature, and certifications.

Warranty Coverage Details

What the Warranty Covers

Details Xantrex's limited warranty coverage for defects in workmanship and materials.

Proof of Purchase and Exclusions

Requirements for claims and conditions not covered by warranty.

Warranty Limitations and Disclaimer

Warranty Limitations and Exclusions

Specific conditions and types of damage not covered by the limited warranty.

Product Disclaimer and Liability

Limitation of Xantrex's liability and warranty terms.

Return Material Authorization Policy

The XPower PowerSource 1800 is an advanced power electronics device designed to provide backup power for various electronic devices and small household appliances. Manufactured by Xantrex Technology Inc., a leading supplier in power electronics, this unit is suitable for both home and small office environments. It functions as a standby UPS (Uninterruptible Power Supply), automatically providing AC power from its internal battery when utility power is unavailable or falls below 105 VAC.

Function Description

The primary function of the PowerSource 1800 is to supply continuous AC power to connected devices, especially during power outages, brownouts, or over-voltages. It converts DC power from its internal battery pack into AC power, mimicking a normal household wall outlet. The unit has a continuous output power rating of 1440 watts and a peak output of 1800 watts, with a surge capacity of 2880 watts, making it capable of running a variety of loads.

When utility power is present, the PowerSource 1800 acts as a pass-through, providing AC power directly from the wall outlet to the connected devices. Simultaneously, it recharges its internal battery. In the event of a power interruption, the unit seamlessly switches to battery backup mode, ensuring uninterrupted operation for connected electronics. The transfer switch operates quickly, typically under 80 milliseconds, to prevent disruption.

The PowerSource 1800 features five 120V AC outlets—one in the front and four in the rear. All these outlets are surge protected and backed up by the internal battery. This means that devices plugged into any of these outlets will continue to receive power during an outage.

Usage Features

The PowerSource 1800 is designed for ease of use with several intuitive features:

Power Button: This button is used to turn the PowerSource 1800 on and off when utility power is not available. A press and hold for at least half a second activates or deactivates the unit. When utility power is present, the Power button cannot be used to remove power from the AC outlets, ensuring continuous power supply.
AC Power/Battery LED: This indicator illuminates green when utility power is available, signifying that the unit is operating normally and potentially charging. It flashes amber when the PowerSource 1800 is providing backup power from its internal battery, alerting the user to a power outage.
LED Screen: A clear LED screen provides essential information about the unit's status. It displays charging status, the power draw from the PowerSource 1800 in watts (W) when providing backup power, or the battery capacity in percentage (%). The screen also shows error codes to assist with troubleshooting, such as "CHG" when recharging or "FUL" when fully charged.
Select Button: This button allows the user to toggle between displaying the PowerSource 1800 Battery Level (%) and the Output Power (W) on the LED screen. This helps users monitor their power consumption and remaining battery life.
Charged/Charging LED: This green LED illuminates steadily when the PowerSource 1800 is fully recharged and flashes while the unit is actively recharging its internal battery.
Fault LED: This red LED illuminates when the PowerSource 1800 encounters an operational fault, indicating a problem that requires attention.
Blue LED: A blue LED illuminates the rear AC outlets when AC power is available, confirming that these outlets are active.
Supplementary Protector: A 15 A supplementary protector is included to protect the PowerSource 1800 AC outlets and connected applications from overload conditions. This acts as a breaker that can be reset if tripped.

Operation Guidelines:

Installation: The unit should be plugged directly into a wall outlet, not into a surge protector or power strip. Electronic devices and appliances are then connected to the PowerSource 1800's AC outlets.
Ventilation: During installation, it's important to allow a minimum of 3 inches of space around the unit for optimal ventilation to prevent overheating.
Backup Power Activation: To activate the AC outlets for backup operation, the unit must be turned on using the Power button.
Run Time: The PowerSource 1800 can run connected products for up to 10 hours, depending on the power draw. Examples of run times for typical products are provided in the manual, ranging from 63 hours for a cordless phone to 12 minutes for a microwave.
Rechargeable Appliances: The unit outputs a non-sinusoidal modified sine wave when on battery backup. Users should be aware that certain types of load equipment, particularly some chargers for rechargeable batteries and appliances with speed controllers, may be damaged by this waveform. It is recommended to contact the equipment manufacturer if unsure about compatibility.
Overload Protection: If the total power consumption of connected devices exceeds the unit's continuous or surge capacity, the unit may shut down, and an error code will be displayed. The supplementary protector may also trip.
Temperature Management: The unit is designed for indoor use in a clean, temperature-controlled environment. Over-temperature warnings and shutdowns can occur if ventilation is poor or ambient temperatures are too high.

Maintenance Features

Battery Charging: The PowerSource 1800 automatically recharges its internal battery when utility power is restored. A complete charge can take up to 15 hours from a 120 VAC wall outlet. It is crucial to charge the unit before storage or use to prevent total battery discharge and ensure extended run time.
Troubleshooting: The LED screen displays error codes (e.g., E01 for low voltage shutdown, E03 for overload shutdown, E04 for over-temperature shutdown, E05 for under-voltage warning, E06 for over-temperature warning) to help users diagnose and resolve common issues. The manual provides a detailed troubleshooting reference with possible causes and solutions for various conditions and symptoms.
Battery Replacement: The battery pack consists of three 17 amp-hour sealed lead acid (AGM) batteries. When these batteries reach the end of their useful service life, they can be replaced by a qualified battery technician. Suitable replacement batteries are specified (e.g., Panasonic® #LC-X1220P and EnerSys™ #NPX-80). Information on replacement battery brands and dealers can be found on the Xantrex Support site.
Recycling: Due to the lead content in the internal batteries, the PowerSource 1800 and its batteries should be recycled or disposed of safely at a local recycling depot. They should not be discarded with common household waste.

Safety Instructions

The PowerSource 1800 generates potentially lethal AC power. Users are warned against inserting foreign objects into AC outlets or ventilation holes and exposing the product to water, rain, snow, or spray. It should not be used with life support systems or other medical equipment. The unit should not be used where flammable fumes or gases are present, as there is an explosion hazard. The cover should not be removed, as there are no user-serviceable parts inside, and servicing should be referred to qualified personnel. Batteries can present a risk of burns from high short-circuit currents.

The unit will not work when connected to any AC load that has its neutral conductor connected to ground, such as AC distribution wiring or house wiring. This is an important consideration for proper installation and operation.