Xtricity 4-80053 User Manual

INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Before you begin installing, servicing, or maintenance of this product, follow these general precautions.
• For commercial installation:serviceandmaintenanceofthisproductshouldbeperformedbyaqualied,licensedelectrician.
• For residential installation:Ifyouareunsureabouttheinstallationormaintenanceofthisproduct,consultaqualied
licensed electrician.
• Donotmounttheunitagainstammablesurfaces.
• Thisproductisintendedtobeusedoutdoors,andbesubjecttotheelements;suchasrainandsnowandwerecommendit
to be mounted at least 6’ 6” off the ground
• ThisLEDproductmustbepowereddirectlytoaswitchedcircuit.(on/off).
• Thisproductshouldnotbeusedinareaswithlimitedventilationorhighambienttemperatures.
• ThisproductCANNOTbeusedwithadimmerswitch,motionoroccupancysensororotherelectronicswitchingdevice.
• ThisproductisintendedtobeconnectedtoaproperlyinstalledandgroundedULlistedjunctionbox.
WARNING: RISK OF ELECTRICAL SHOCK
• Turnoffelectricalpoweratfuseorcircuitbreakerboxbeforewiringproducttothepowersupply.
• Verifyvoltageis110V-240Vbeforeinstalling.
• MakeallelectricalandgroundedconnectionsinaccordancewiththeNationalElectricCodeandanyapplicablelocalcode
 requirementsandAllwiringconnectionsshouldbecappedwithULlistedwireconnectors.
CAUTION: RISK OF PRODUCT DAMAGE
• Neverconnectxturewithpoweron.
• AvoidcoveringLEDproductswithinsulation,foam,orothermaterialsthatwillpreventconvectionorconductioncooling.
• NeverconnectanLEDproductdirectlytodimmerpacks,occupancysensors,timingdevices,orotherrelatedcontroldevices,
 unlessindividualproductspecicationsdeemotherwise.
• LEDproductsarepolaritysensitive,ensureproperpolaritybeforeinstallation.
• Donottouchtheindividualelectroniccomponents,itmaycauseESD(ElectronicDischarge),shortenlamplife
or alter performance.
CAUTION: RISK OF INJURY
• Avoiddirecteyeexposuretothelightsourcewhileitison.
• Letitcoolcompletelybeforehandling.
INSTALLATION INSTRUCTIONS
PART DESCRIPTION QUANTITY
 A LightFixture 1
 B PlasticScrewCover 1
 C StainlessSteelScrew 1
 D Gasket(optional) 1
 E CrossBar 1
 F GroundingScrew 1
 G GroundingWire 1
 H WireNut 3
 I StainlessSteelMountingScrews 2
SiliconSealantrecommended(notincluded)
Tools Required for Installation: Phillips screwdriver, level
LED MOTION SENSOR SECURITY LIGHT
Item:4-80053/4-80054
PRODUCT SPECIFICATIONS
• DetectionMethod:PIR(PassiveInfrared)
• DetectionRange:Max.70ft
• DetectionAngle:Upto240°
• LEDAngle:120°
• TimeAdjustment:(minimum)5secondsto1,5,12minutes
• OperatingVoltage:110~240volts50Hz/60Hz
• IPRating:44
Note:Sensorhasa11/2minutewarmupperiodbeforeitwilldetectmotion.whenrstturnedon,wait11/2minutes.
TROUBLESHOOTING GUIDE
PRODUCT MAINTENANCE
Tocleanthesurfaceofthelight,usemildsoapandwater.
Donotusescouringpads,powders,steelwooloranyotherabrasivematerials.Donotimmerseinwater.
SYMPTOM POSSIBLE CAUSE
Lightswillnotcomeon
1.Lightswitchisturnedoff.
2.Lightislooseorburnedout.
3.Fuseisblownorcircuitbreakeristurnedoff.
4.Daylightturnoffisineffect(recheckafterdark).
5.Incorrectcircuitwiring,ifthisisanewinstallation.
6.Re-aimthesensortocoverdesiredarea
Lightscomeonindaylight. Lightcontrolmaybeinstalledinarelativelydarklocation.
Lightscomeonfor
no apparent reason.
Lightcontrolmaybesensingsmallanimals
orautomobiletrafc(re-aimsensor).
Rangeissettoohigh.(ReduceRangesetting).
Lightsstayoncontinuously.
1.Alampispositionedtooclosetothesensororpointed
atnearbyobjectsthatcauseheattotriggerthesensor.
(Repositionthelampawayfromthesensoror
nearbyobjects).
2.Reducesensitivity.
Lightsashonandoff.
1.Heatorlightfromthelampsmaybeturningthelight
controlonandoff.(Repositionthelampsawayfrom
thesensor).
2.Heatbeingreectedfromotherobjectsmaybeaffecting
thesensor.(Repositionsensor).

Xtricity 4-80053 Specifications

General

Brand	Xtricity
Model	4-80053
Category	Flood Light
Language	English

Summary

Product Specifications

Instructions and Safety

Important Safety Instructions

Crucial safety precautions before installation, servicing, or maintenance.

Electrical Shock Warning

Warnings about electrical shock hazards and necessary precautions during wiring.

Product Damage Caution

Precautions to prevent damage to the LED product during installation and use.

Risk of Injury Warning

Warnings about potential injury, especially from direct eye exposure to the light.

Installation Instructions Overview

Lists parts and tools required for installing the motion sensor security light.

Product Maintenance Guidelines

Guidelines for cleaning and maintaining the light fixture's surface using mild soap.

Troubleshooting Guide

Lights Will Not Come On

Addresses common causes and solutions when the light fails to activate.

Lights Come On In Daylight

Explains why the light may activate during daylight hours.

Lights Activate Without Apparent Reason

Discusses causes for the light activating unexpectedly or falsely.

Lights Stay On Continuously

Provides reasons why the light might stay illuminated without interruption.

Lights Flash On and Off

Explains causes for the light flickering or cycling on and off repeatedly.

Mounting and Wiring

Mounting and Wiring the Light

Step-by-step guide for physically mounting the fixture and connecting wires.

Adjusting Light Heads

Instructions on how to position the individual light heads for desired coverage.

Sensor and Time Adjustments

Adjusting Motion Sensor

Guide to adjusting the sensor head up/down for optimal detection range.

Setting the Motion Sensor

Details on setting detection range, time, and sensitivity for the motion sensor.

LUX Settings

Explanation of how to adjust the light sensitivity based on ambient darkness.

SENS Settings

Guide to adjusting the motion sensor's sensitivity level (Min, Mid, Max).