Yale GLP60VX

Steering Axle Assembly Repair 1600 YRM 1133
See Figure 7 for lift truck models
• GLC/GDC60VX, GLC/GDC70VX, (GC/GLC/
GDC135VX, GC/GLC/GDC155VX) (C879,
D879, E879, F879)
See Figure 8 for lift truck models
• GLP/GDP60VX, GLP/GDP70VX (GP/GLP/
GDP135VX, GP/GLP/GDP155VX) (C878,
D878, E878)
• GLP/GDP80VX, GLP/GDP80VX9,
GLP/GDP90VX (GLP/GDP170VX,
GLP/GDP170VX36, GLP/GDP190VX)
(A909, B909)
c. Remove plates and slowly lower steering axle
assembly onto wheels. Carefully roll steering
axle assembly away from lift truck.
DISASSEMBLE
1. Remove ring seal, shims, flange, stub shaft and
bushingfromsteeringaxleassemblyforlifttruck
models below.
See Figure 8 for lift truck models
• GLP/GDP60VX, GLP/GDP70VX (GP/GLP/
GDP135VX, GP/GLP/GDP155VX) (C878, D878,
E878)
• GLP/GDP80VX, GLP/GDP80VX9,
GLP/GDP90VX (GLP/GDP170VX,
GLP/GDP170VX36, GLP/GDP190VX) (A909,
B909)
2. Put axle on blocks so the wheels just touch the floor.
Remove hub cap. Remove cotter pin, washer, and
castle nut. Remove bearing cone and discard cot-
ter pin.
NOTE: Identify and tag the outer and inner bearing
cones so they can be reassembled in their original
locations.
NOTE: The wear ring may not be present on all steering
axles.
3. Slide wheel from spindle. Remove inner bearing
cone, wear ring, and oil seal from spindle.
See Figure 2 for lift truck model
• GLC20-35VX (GC/GLC040-070VX,
GC/GLC055SVX) (A910)
See Figure 3 for lift truck model
• GLP/GDP20-35VX (GP/GLP/GDP040-070VX)
(B875)
See Figure 4 for lift truck models
• GC/GLC030-035VX, GC/GLC040SVX (C809)
• GLP/GDP16-18VX, GLP/GDP20SVX (GP/GLP/
GDP030-035VX, GP/GLP/GDP040SVX) (C810)
See Figure 5 for lift truck model
• GLC40, 45, 55VX; GLC55SVX; (GC/GLC080,
100, 120VX; GC/GLC080, 100VXBCS;
GC/GLC120SVX; GC/GLC120VXPRS) (E818,
F818)
See Figure 6 for lift truck models
• GLP/GDP40VX5/VX6; GLP/GDP45SVX5,
GLP/GDP45VX6; GLP/GDP50-55VX (GP/GLP/
GDP080, 090, 100, 110, 120VX) (F813, G813,
H813, J813)
See Figure 7 for lift truck models
• GLC/GDC60VX, GLC/GDC70VX, (GC/GLC/
GDC135VX, GC/GLC/GDC155VX) (C879, D879,
E879, F879)
See Figure 8 for lift truck models
• GLP/GDP60VX, GLP/GDP70VX (GP/GLP/
GDP135VX, GP/GLP/GDP155VX) (C878, D878,
E878)
• GLP/GDP80VX, GLP/GDP80VX9,
GLP/GDP90VX (GLP/GDP170VX,
GLP/GDP170VX36, GLP/GDP190VX) (A909,
B909)
NOTE: If the bearing is replaced, then the associated
bearing cup must be replaced also.
4. If the bearings must be replaced, use a brass drift
pin to remove the bearing cups and wear ring.
5. Repeat Step 1 through Step 4 for the other wheel.
4