To Next Page
J
Jamie AlvarezSep 6, 2025
How to setup Yamaha 50HMHO Outboard Motor tachometer to show the oil pressure?
- MmichellelarsenSep 6, 2025
Select the oil press. display.
How to setup Yamaha 50HMHO Outboard Motor tachometer to show the oil pressure?
Select the oil press. display.
What to do if the Yamaha 50HMHO Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha 50HMHO illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha 50HMHO Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha 50HMHO Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha 50HMHO Outboard Motor gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
What to do if my Yamaha 50HMHO speedometer shows the incorrect fuel level?
If the speedometer shows an incorrect fuel level, the fuel sensor selection is likely wrong. You should set up the fuel sensor to the correct resistance.
What does it mean when my Yamaha 50HMHO Outboard Motor gauge shows “----”?
If the gauge shows “----”, it indicates that the digital signal is not being received. Make sure the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha Outboard Motor boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What causes Yamaha 50HMHO gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
General| Brand | Yamaha |
|---|---|
| Model | 50HMHO |
| Category | Outboard Motor |
| Language | English |
Crucial safety precautions for operating the outboard motor and boat.
Identifies key parts of the outboard motor with diagrams for various models.
Explains neutral interlock, throttle lever, tiller, and gear shift operations.
Details the engine stop lanyard switch and button for operator safety.
Covers choke, manual starter, main switch, and steering adjuster functions.
Explains the operation of power trim and tilt switches and their effects.
Explains warning lights for engine conditions and oil level status.
Explains the overheat warning system and its activation methods.
Details oil level and oil filter clogging warnings and their effects.
Covers correct engine height, mounting procedures, and boat balance.
Details the steps for breaking in a new engine for longevity.
Lists essential checks before starting the engine for safety and function.
Outlines regular maintenance tasks and their intervals.
Detailed chart of maintenance items, actions, and frequencies.
Provides solutions for common engine and operational problems.
Steps to take if the motor sustains impact damage.
Troubleshooting steps when the starter mechanism fails.
Procedure for starting the engine using an emergency starter rope.
Troubleshooting for when the engine fails to start, especially when cold.
Immediate steps to minimize damage if the motor is submerged.
