What to do if Yamaha Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
What to do if the Yamaha E25BMH gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or, if necessary, replace the gauge itself.
Why Yamaha E25BMH Outboard Motor illumination does not light?
If the illumination does not light, it could be due to a lack of electrical power or a damaged gauge. You should try replacing the fuse, connecting the couplers securely, replacing the damaged wire or hub, or replacing the gauge.
How to fix Yamaha Outboard Motor tachometer showing incorrect engine RPM?
If the tachometer shows an incorrect engine RPM, the engine recognition might be wrong (especially for multi-applications). To correct this, push the 'SET' button for 10 seconds to default the engine number, then memorize each engine number again.
What causes Yamaha E25BMH Outboard Motor fuel management gauge to show incorrect remaining fuel?
If the fuel management gauge shows incorrect remaining fuel, the fuel capacity setting may be wrong (specifically for SQR Fuel mgt Gauge). Fill the tank with fuel, and set the correct fuel tank capacity.
What to do if Yamaha E25BMH gauge shows “----”?
If the gauge displays '----', it indicates that the digital signal is not being received. Check that the couplers are securely connected and replace any damaged bus wires or hubs.
Why Yamaha E25BMH Speedometer or Comb. Speedometer & Fuel mgt gauge shows incorrect fuel level?
If the speedometer or combination speedometer & fuel management gauge shows an incorrect fuel level, the fuel sensor selection is likely wrong. Set up the fuel sensor to the correct resistance.
How to fix Yamaha E25BMH Outboard Motor trim gauge showing incorrect position?
If the trim gauge shows an incorrect position, the initial position setting might be wrong, or the trim sender could be damaged. Put the motor in the fully trimmed-in position and reset the initial (zero) trim angle. If that doesn't work, replace the trim sender.
Why Yamaha E25BMH Outboard Motor gauge operates unstably?
If the gauge operates unstably, it could be because a resistor is not connected to the ending hubs. Connect the gray 6-pin cap to the ending multi-hubs.
What causes Yamaha Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Instructions could result in severe injury or death.
Steps for safely removing the outboard motor from its crate.
Procedures for correctly mounting the outboard motor onto the transom.
Guidance on selecting the appropriate propeller.
Table of Wide-Open-Throttle RPM ranges for propeller selection.
Description and applications of the 701 Remote Control.
Description and applications of the 704 Remote Control.
Description and applications of the 6X3 Remote Control.
Description of 6X6 Digital Electronic Control remote for F250-F350.
Description of 6X7 Digital Electronic Control remote for F250-F350.
Procedures for mounting instrument meters.
Analog tachometer description and applications.
Digital tachometer description and applications.
Speedometer description and applications.
Fuel management gauge description and applications.
Analog trim meter description and applications.
Coolant pressure meter description and applications.
Battery wiring procedures.
General| Engine Type | 2-Stroke |
|---|---|
| Max Output | 25 HP |
| Max. Output (kW) | 18.4 kW |
| Max. Output (PS) @ RPM | 25 PS @ 5000 RPM |
| Starting System | Manual |
| Ignition System | CDI |
| Gear Ratio | 2.08:1 |
| Steering | Tiller |
| Fuel Induction System | Carburetor |
| Lubrication System | Premix |
| Shaft Length | L (508 mm) |
| Full Throttle RPM Range | 4500 - 5500 RPM |
| Fuel System | Carburetor |
To Next Page
