To Next PageTo Next Page
Need help?Do you have a question about the Yamaha RX-V595aRDS and is the answer not in the manual?
General| Power Output | 100 W per channel (8 ohms, 20 Hz - 20 kHz, 0.08% THD) |
|---|---|
| Channels | 5.1 |
| Frequency Response | 10 Hz - 100 kHz |
| Input Sensitivity | 2.5mV (MM), 150mV (line) |
| Signal-to-Noise Ratio | 86dB (MM), 100dB (line) |
| Weight | 10.5kg |
| Speaker load impedance | 6 - 16 ohms |
| Video Connections | Composite, S-Video |
| Tuning range | FM: 87.5 - 108 MHz, AM: 531 - 1602 kHz |
| Total harmonic distortion | 0.04% |
| Damping factor | 100 |
| Signal to noise ratio | 100 dB |
| Channel separation | 50 dB |
| Amplifier Section | Discrete |
| Input Sensitivity/Impedance | 200 mV / 47 kOhm |
| Tuner Section | FM/AM |
| Power Supply | AC 220 - 240 V, 50/60 Hz |
Lists the included indoor FM antenna.
Details the included AM loop antenna.
Describes the 75/300-ohm antenna adapter for UK models.
Information on the included remote control and its battery.
Specifies the type of batteries required (AA, R6, UM-3).
Specifies the RMS output power for each channel.
Explains DSP capabilities including Dolby Digital, Pro Logic, DTS.
Details FM/AM tuning features like preset tuning.
Covers video signal handling including S-Video.
Information on setting the unit's sleep timer function.
Notes on the remote's preset manufacturer codes.
Lists essential safety guidelines for operating the unit.
Provides specific wiring guidance for U.K. models.
Explains how DSP recreates concert hall acoustics.
Details the Dolby Pro Logic decoder and its home theater application.
Explains the 5.1 channel Dolby Digital system.
Details the DTS 5.1 channel surround sound system.
Explains the YAMAHA CINEMA DSP logo and its function.
Describes DSP programs for Dolby Pro Logic sources.
Describes DSP programs for Dolby Digital or DTS sources.
Turns the unit on or sets it to standby mode.
Receives signals from the remote control.
Shows various information about the unit's status.
For storing stations and automatic preset tuning.
Used to exchange the assignment of two preset stations.
Switches between automatic and manual tuning modes.
Switches the reception band between FM and AM.
Used for tuning to desired stations.
Selects tape/MD source or external decoder input.
Selects the desired input source (VCR, DVD, CD, etc.).
Switches between DVD/LD and TV/DBS input signal modes.
Used to raise or lower the volume level.
Connects headphones for private listening.
Turns main speaker systems (A or B) ON or OFF.
Selects preset station groups (A-E) and numbers (1-8).
Adjusts Bass, Treble, and speaker Balance.
Changes display mode among RDS data services.
Initiates program type search and EON function.
Accesses TIME/LEVEL mode and SET MENU functions.
Selects DSP programs and turns sound effects ON/OFF.
Connects auxiliary video sources like camcorders.
Shows station frequency, input source, and other info.
Details the meaning of indicators like MEMORY, STEREO, DTS.
Guidelines on selecting main, center, and rear speakers.
Diagram and instructions for optimal speaker positioning.
Information on connecting a subwoofer for enhanced sound.
General guidance for connecting audio/video components via RCA.
Details on using switched AC outlets for component power.
Instructions for connecting the turntable ground wire.
Connecting sources via digital coaxial or optical signals.
Specifics for connecting DVD/LD players digitally.
Details for connecting TV/DBS tuners digitally.
Explanation of S-Video terminals and signal separation.
Connecting front-panel auxiliary video sources.
Using SCART cables for monitor connection.
Input terminals for 6-channel audio from external decoders.
Setting the impedance selector based on speaker requirements.
Guidelines for connecting one or two main speaker systems.
Instructions for connecting rear speaker systems.
Placement and connection advice for the center speaker.
Connecting a subwoofer system to the unit.
Step-by-step guide for connecting main speaker wires.
Step-by-step guide for rear and center speaker wires.
Terminals for driving speakers with an external amplifier.
Instructions for connecting indoor and outdoor FM antennas.
Guide for connecting the AM loop antenna.
Importance of connecting the GND terminal for safety and interference.
Setting speaker distribution modes (CNTR, REAR, MAIN, BASS, M.LVL).
Detailed explanation of each speaker output mode setting.
Step-by-step guide for adjusting speaker output modes.
Setting selector dial, turning on power, selecting main speakers.
Choosing which main speaker systems to use for adjustment.
Setting BASS/TREBLE/BALANCE and initiating test tone.
Adjusting speaker balance using the test tone output.
Fine-tuning center and rear speaker output levels.
Notes on overall volume control and memory backup.
How to select sources using INPUT on front panel or remote.
Steps to play audio from tape decks or MD recorders.
How to select sources connected to external decoder inputs.
Switching input modes for specific sources.
Fine-tuning audio playback settings.
Important considerations when selecting input sources.
Explanation of input mode selection for DVD/LD/TV/DBS.
Specific advice for playing DTS encoded sources.
Steps to record audio/video sources onto tape or MD.
Important notes regarding recording and copyright laws.
Using automatic search tuning for strong station signals.
Manually tuning to stations, especially weak ones.
Procedure for storing tuned stations into memory.
Steps to select and recall stored preset stations.
Details on memory back-up and data loss prevention.
Procedure for automatically storing RDS stations.
Options for assigning specific preset numbers to stored stations.
How to swap the assignment of two preset stations.
Explanation of RDS data types like PS, PTY, RT, CT, EON.
How to cycle through available RDS display modes.
Steps to search for stations by program type.
List of 15 program types for RDS station classification.
Automatically monitoring and switching to designated program types.
How to turn off the EON function.
Procedure to set the unit to automatically switch to standby.
How to cancel an active sleep timer setting.
Describes Normal Program types: Dolby Pro Logic, Dolby Digital.
Details CINEMA DSP programs like 70mm Movie Theater.
Describes Hi-Fi programs like DISCO and ROCK CONCERT.
How to select and activate DSP programs.
Turning off DSP sound effects to monitor original sound.
Explains the meaning of DSP-related indicators on the display.
Steps for adjusting delay time and speaker output levels.
Choosing items like DELAY, CENTER, SWFR for adjustment.
Control ranges and preset values for delay time.
Setting output levels for center, rear, and subwoofer.
Information on how settings are backed up and restored.
Adjusting the LFE channel level for Dolby Digital sources.
Adjusting dynamic range for Dolby Digital sources (MAX/STD/MIN).
Adjusting the LFE channel level for DTS sources.
Adjusting the delay for center channel sounds (dialog).
Locking SET MENU and TIME/LEVEL settings.
Selecting the default input mode for TV/DBS sources.
Procedure for making adjustments in the SET MENU.
Selector Dial positions for controlling various components.
Selecting component and pressing operation buttons.
Functions of remote buttons when SELECTOR DIAL is on AMP/TUN.
Functions for selecting DSP programs via remote.
Remote functions for controlling tape decks and MD recorders.
Remote functions for controlling CD players.
Remote functions for controlling DVD/LD players.
Remote functions for navigating DVD menus.
Remote functions for controlling VCRs.
Remote functions for controlling TVs.
Remote functions for controlling Cable/DBS tuners.
Guide to installing, replacing, and handling remote batteries.
Factors affecting remote control performance and range.
Steps for programming the remote to control other components.
Procedure to reset remote control to factory default codes.
Table of factory preset codes for various components.
Troubleshooting power-on failures and operational problems.
Resolving issues related to no sound or no picture.
Addressing speaker connection, hum, and volume level problems.
Troubleshooting no sound from effect, rear, or center speakers.
Resolving recording failures and noisy FM reception.
Addressing tuning difficulties and various noise types.
Resolving remote control malfunctions and noise interference.
Troubleshooting sound problems when playing DTS sources.
Details on output power, distortion, S/N ratio, frequency response.
Specifications for FM and AM tuning capabilities.
Details on video signal types and levels.
Information on power supply, dimensions, weight, and accessories.
List of manufacturer codes for TV components.
List of manufacturer codes for Cable and DBS tuners.
List of manufacturer codes for DVD/LD players.
List of manufacturer codes for CD players.
List of manufacturer codes for MD recorders.
List of manufacturer codes for tape decks.
