Yardbeast YB2090 User Manual

These are some of the wood chipper
features and controls you should be aware
of to familiarize yourself with the chipper.
It is very important you understand
components for a safe operation of the
machine and further instruct someone else
on the operation of this chipper if needed.
Feed Hopper:
You can allow the entry of
wood up to 3-
1/2 "diameter in the hopper to
be chopped.
You will find that more dry
mater
ial will be harder to chip but more
brittle as opposed to green material which is
softer in hardness. The chipper naturally
performs better self feeding action on green
material over dry material.
WARNING
When operating the
wood
use safety protection,
this chipper
expels wood chips with great force
by design.
IMPORTANT: Never place
wood
hopper with
a diameter greater than
Doing so could
damage the blades
jeopardize the integrity
of the machine.
Clutch:
The clutch is a transmission coupling
mechanism that engages and disengages
automatically by the engine RPM's. If you
are chipping at top chipper capacity and
the engine stalls below the engaging
minimum engine RPM, the chipper rotor will
stop while the en
gine won't. It is important
that you siwftly throttle the engine down to
idle position to fully disengage the clutch to
avoind overload on the clutch shoes and
improve the overall clutch's operational life.
ENGINE: See engine operation
manual
came with your unit. This
is located
the manual holder
for the location
operation of the motor.
MANUAL CANISTER: Keep the
user manual
These are some of the wood chipper
features and controls you should be aware
of to familiarize yourself with the chipper.
It is very important you understand
these
components for a safe operation of the
machine and further instruct someone else
on the operation of this chipper if needed.
You can allow the entry of
1/2 "diameter in the hopper to
You will find that more dry
ial will be harder to chip but more
brittle as opposed to green material which is
softer in hardness. The chipper naturally
performs better self feeding action on green
wood
chipper,
this chipper
expels wood chips with great force
wood
in the
a diameter greater than
3-1/2 ".
damage the blades
and
of the machine.
The clutch is a transmission coupling
mechanism that engages and disengages
automatically by the engine RPM's. If you
are chipping at top chipper capacity and
the engine stalls below the engaging
minimum engine RPM, the chipper rotor will
gine won't. It is important
that you siwftly throttle the engine down to
idle position to fully disengage the clutch to
avoind overload on the clutch shoes and
improve the overall clutch's operational life.
manual
that
is located
inside
for the location
and
user manual
of
the chipper and
the engine
manual canister –
as well as safety
accessories if needed-
for future refer
DISCHARGE DEFLECTOR:
use
deflector
to adjust the distance
of material to be chopped.
WARNING
Use
protective gear
adjust the
discharge neck
is done without
protection
seriously damage the eyes
and
and body damage.
Working with your Wood Chipper
The material to
be chipped
cutting area
through the
where this
is impacted by
which together with the
anvil
scissor cutting effect.
Once cut
desintegrated by the
impact hammers and
flails, the material is
radially
the discharge screen
onto the ground.
When shredding, the material enters the
cutting area through the top chute. This
material is cut and torn apart by a mixed
combination of cutting flails, which helps to
reduce the branches, and the hammers
that impact the material against the screens
until
their size is reduced enough to pass
through the screen.
Starting your Engine
WARNING
Never run an
engine indoors
a
poorly ventilated area
exhaust contains
carbon monoxide,
odorless and deadly gas.
To start the engine, please
follow these
steps:
13
the engine
inside the
as well as safety
for future refer
ence.
use
the discharge
to adjust the distance
of discharge
protective gear
,and to
discharge neck
, if this
protection
, it can
and
cause facial
Working with your Wood Chipper
be chipped
enters the
through the
feed hopper
is impacted by
a sharp blade,
anvil
, produces a
Once cut
and
impact hammers and
radially
ejected through
onto the ground.
When shredding, the material enters the
cutting area through the top chute. This
material is cut and torn apart by a mixed
combination of cutting flails, which helps to
reduce the branches, and the hammers
that impact the material against the screens
their size is reduced enough to pass
engine indoors
or in
poorly ventilated area
. Engine
carbon monoxide,
an
follow these

Yardbeast YB2090 Specifications

General

Brand	Yardbeast
Model	YB2090
Category	Other
Language	English