Yueming CMA1610-T-A - User Manual

Questions and Answers

M
Michael AcevedoAug 13, 2025
What to do if my Yueming CMA1610-T-A cutting graphics and drawing size do not match?
- D
  Dylan LongAug 14, 2025
  If the cutting graphics and drawing size on your Yueming Cutter do not match, there are several potential causes. First, there may be a program input error, so check the procedures according to the figure. Second, the synchronous belt may be loose, in which case you should tension it. Finally, the control system could be damaged; inspect the stepper motor and drive, and replace them if necessary.
E
Emily BrownAug 17, 2025
What to do if Yueming Cutter equipment crashes and is carving?
- C
  Chad VillanuevaAug 17, 2025
  If your Yueming Cutter is crashing and carving, it could be due to a few reasons. The laser tube (high voltage) might be discharging to the housing and sparking; if so, reconnect the high-voltage line of the laser tube. Alternatively, the board may not be grounded or there may be other interference. Ensure you properly connect the ground wire and eliminate any interference.
L
Lucas ByrdAug 21, 2025
What to do if the laser tube can’t work on Yueming CMA1610-T-A Cutter?
- J
  Joseph PerryAug 21, 2025
  If the laser tube on your Yueming Cutter isn’t working, first ensure the water-cooling system is turned on normally by turning on the water circulation system. Also, check if the chiller is working properly and press the laser power button. If these steps don't solve the issue, the laser power supply may be damaged, and you should replace it with a switching power supply of the same specifications.
E
Eric AndersonAug 25, 2025
What to do if the Yueming CMA1610-T-A equipment can’t be turned on?
- M
  Maurice JimenezAug 26, 2025
  If your Yueming Cutter equipment won’t turn on, make sure to release the emergency stop button. Also, reset the main contactor and ensure that the front cover and back cover are properly in place.
R
rachel19Aug 29, 2025
What to do if I get the wrong figure size on my Yueming CMA1610-T-A?
- J
  Jonathan RodriguezAug 29, 2025
  If you're getting the wrong figure size with your Yueming Cutter, and you are using PLT output in CorelDraw software, ensure the PLT plotter unit out from CorelDraw software matches the resolution of SmartCarve software lead-in PLT option. Also, confirm that the zooming in the page option is set to 100%. Ensure you set to the correct resolution or equivalent. Other possible causes include failing to connect earthing for the mainboard or other interferences, in which case you should connect earthing to eliminate the interference. Finally, over high temperature can cause a crash to the mainboard, so add more measures for lowering temperature.
Z
zcortezSep 1, 2025
Why does the laser pause during working on my Yueming CMA1610-T-A Cutter?
- P
  Paul TorresSep 1, 2025
  If the laser pauses during operation on your Yueming Cutter, you should clean the water tank and dredge the water hose. Additionally, install a stabilizer to the input power supply.
D
Donald MooreSep 5, 2025
Why is there reverse direction of motor shaft movement in Yueming Cutter?
- A
  alexandra85Sep 5, 2025
  To address reverse direction of motor shaft movement in your Yueming Cutter, check electric earthing and drive parameter settings.
J
jameswebbSep 9, 2025
What to do if the motor shaft fails in movement or twitters during movement on my Yueming Cutter?
- W
  wendy58Sep 9, 2025
  If the motor shaft fails to move or twitters during movement on your Yueming Cutter, it could be due to improper setting of motor parameters, so set to the correct movement parameters. Alternatively, the drive or motor may be damaged, requiring you to change the drive or motor. Finally, reconnect the motor and drive line.